Fe DOX Rust Remover (Concentrated) is specially developed for de-rusting of steel parts & inner tank surfaces. It can be diluted in water, with a maximum dilution ratio of 1:10. The parts to be derusted are then immersed in the solution. The solution can be heated up to 65°C for faster derusting. The duration of derusting varies depending on the thickness of the parts. Flash rust is removed within 15-45 minutes while a thicker layer of rust takes up to 12-24 hours of time. Post de-rusting the components should be washed with water & coated thereafter immediately with any kind of waxes or primers. Can be used for derusting of: Tools & metal parts Casings Turbines & machine parts Interior surface of a tank, et. al. ...

Description & characteristics Flash rust is a common problem with iron & steel & indicates that permanent corrosion will arise unless the flash rust is treated prior to further coatings. Fertan Rust Film Remover is the ideal product to remove corrosion. FRFR is safe to use ono painted & polished surface. Also excellent on tired galvanised surfaces. FRFR carries out the rust removal process itself with no intervention necessary. The spray works in just a few minutes & gently removes rust film from all your projects. Easy to use & changes to a red colour when the cleaning is complete. Application & instructions for use To achieve the best possible cleaning results spray the affected areas. Let the spray work for some time until the colour changes to red. Then rinse off the residue with plain water.  Dry at once using moderate heat. Use Fertan Rust Converter or a primer promptly to avoid flash rust re-occuring. Processing tools No processing tools are necessary. ...

Multi-metal coating with aluminum-titanium-zinc cathodic long-term corrosion protection. Extremely resistant & very high-quality surface quality after full hardening. Very good adhesion to steel, aluminum, & copper, can be overpainted as a bonding bridge with commercially available 1-component & 2-component paints. Spot weldable. Resistance over 500 hours at only 15 μm in salt spray test. Use on car bodies, steel frames, steel construction, heating & ventilation construction & industry. Application: Shake can for at least 3 minutes before use. The substrate must be clean, dry, free of grease & silicone. Remove rust beforehand with FERTAN. For optimum effect, apply a thin layer of M M 30 Spray in 1-2 spraying cycles, spray distance at least 15 – 25 cm. After use, spray over the head of the spray valve. Dust-dry after approx. 5 – 10 min. Touch-proof after approx. 1 hour. Complete hardening after 2-3 days at 20° C in each case. Temperature resistant up to 300° C. ...

Multiöl is a multifunctional spray for the cleaning & care of metal parts & plastics, for the lubrication of metal compounds & as corrosion protection on metallic surfaces.  Prevents icing of lock cylinders & displaces moisture on electronic components. Universally applicable Simple application Maintains & protects metal & plastic surfaces Prevents icing of lock cylinders & displaces moisture on electronic components. Resin, acid & silicone free – Does not attack rubber, paint & plastics Dissolves rust   Application: Shake well before use. Spray on thinly & allow a few moments for it to work, then carefully loosen corroded items Wipe off excess material with a damp cloth Storage: Store in a cool, well-ventilated place. ...

Pre Wax is a specially developed pre-treatment wax for vehicle bodies. It is used to thin-coat the previously rusted sheet metal rebate with a very fine, extremely stable & creepable wax, which penetrates the seams & has been previously derusted with FERTAN. The final coating is applied individually to the underbody with UBS 240 Underbody Protection Wax or in cavities, sills, etc. with Cavity Protection Wax. The pre-treatment with Pre Wax ensures that even firmly placed sheet metal & sheet metal joints are permanently protected in the area of the weld seam, as the product penetrates these joints. The product can also be sprayed on the outside to protect metal from the outside & leaves a very thin but stable protective film on the object to be protected. Product residues are easy to remove with white spirit. Application: Spray the product directly onto or into the folds of folds, overlaps, etc. from a short distance. In cavities, sills etc. spray the product with the enclosed Ø 4 mm probe into the cavity & slowly pull the probe through. The penetration is clearly visible at weld seams/overlaps etc.. Since it cannot be ruled out that the excess product will run off due to the viscosity, cover the floor & remove product residues on objects as immediately as possible with white spirit. ...

The purpose of Fertan Rust Converter is to provide you with all the benefits of shot blasting with no surface damage & no material loss. As there is no blasting the process is nuisance free & silent.  You are able to observe & be sure that all the rust has been converted before applying opaque paint coats. Fertan is suitable for treating steel & iron surfaces, even if they have to be left for weeks or months prior to final painting.  Rust is removed & prevented from re-forming for up to six months so delays in your painting schedule will not be a disaster. It can be over-coated with oil or water based paints, epoxy, lacquer, wax etc. It is a complex, patented tannic acid, water based non toxic product.  It offers exceptional protection against rust despite being environmentally friendly.  Isocyanates & high volatiles are not necessary so it doesn't contain them. Fertan converts loose rust to powder that can be rinsed away leaving a converted stable & inert surface. When kept in closed containers & reasonable conditions it has an unlimited shelf life.   Application is simple & safe…. 1. Loosen surface rust using a brush, abrasives or pressure washer. 2. Apply FERTAN using a brush, roller or sponge & let it sit for about an hour. 3. Dampen the treated surface with water to maximize penetration. 4. Leave FERTAN to react with the surface for 24 hours at 68°F to 48 hours if lower for best results. 5. Remove the black powdery dust with a damp cloth & leave it to dry. 6. Paint the treated surface with paint within 6 months, for effective long-term results. ...

The purpose of Fertan Rust Converter is to provide you with all the benefits of shot blasting with no surface damage & no material loss. As there is no blasting the process is nuisance free & silent.  You are able to observe & be sure that all the rust has been converted before applying opaque paint coats. Fertan is suitable for treating steel & iron surfaces, even if they have to be left for weeks or months prior to final painting.  Rust is removed & prevented from re-forming for up to six months so delays in your painting schedule will not be a disaster. It can be over-coated with oil or water based paints, epoxy, lacquer, wax etc. It is a complex, patented tannic acid, water based non toxic product.  It offers exceptional protection against rust despite being environmentally friendly.  Isocyanates & high volatiles are not necessary so it doesn't contain them. Fertan converts loose rust to powder that can be rinsed away leaving a converted stable & inert surface. When kept in closed containers & reasonable conditions it has an unlimited shelf life.   Application is simple & safe…. 1. Loosen surface rust using a brush, abrasives or pressure washer. 2. Apply FERTAN using a brush, roller or sponge & let it sit for about an hour. 3. Dampen the treated surface with water to maximize penetration. 4. Leave FERTAN to react with the surface for 24 hours at 68°F to 48 hours if lower for best results. 5. Remove the black powdery dust with a damp cloth & leave it to dry. 6. Paint the treated surface with paint within 6 months, for effective long-term results. ...

Using Sealeater is the easiest & most complete way of removing old linings from motorcycle fuel tanks.  It works by attacking the chemical bonds of tank linings & allows the complete removal of linings. This is impossible by mechanical means & unlikely with other chemicals. Many motorcycle tanks are lined with poorly designed & poorly installed linings.  Poorly designed as they were not meant to cope with fuel containing ethanol & poorly installed as they’ve been applied to tanks with corrosion present.  Ethanol dissolves polyester based resins & carries them into the fuel system. As the lining is attacked tanks begin to leak again. For many years motorcycle tanks have been lined with products with a primary purpose of resolving pin hole leaks, bad seams & general seepage.    With leaded fuel this was, if not perfect, satisfactory. With the arrival of ethanol in fuels it has become necessary to protect all tanks from being attacked by the ethanol component itself & the water that it brings into the tank.  Ethanol fuel is allowed to be 2% water & it is also hydroscopic, encouraging atmospheric water to join with it. Ethanol itself attacks aluminium & rubber like compounds. All in all, a joy. Use is simple.  Ensure you can make the tank vapour tight. Tip in Seal Eater & close tank.  Check after 2 hours.  In that time the simpler liners will have failed & form a sludge to be tipped from the tank.  If that is not the case you have a good quality epoxy liner.  Seal the tank & leave for 5 days. At that point the liner will be in the liquid either in solution or in flakes.  You can pick up & agitate the tank at any time but it does not have a significant affect. Sealeater is a very volatile & energetic compound.  If it is being used in a painted tank then care must be taken to avoid Sealeater or its vapours coming into contact with the outside of the tank. NOT to be used in a GRP or FRP fuel tank. ...

Product Features Fuel resistant Ethanol resistant Temperature resistant up to 80°C Application: Before use, stir the TAPOX very well, add hardener & mix to a completely thin coating. Please note that TAPOX is a resin & not a paint & must, therefore, be stirred longer to obtain the completely thin mixture! Clean the tank very thoroughly before the internal coating, derust it & protect it against new corrosion with Fertan Rust Remover. Only apply the TAPOX coating in a completely dry tank. Follow the processing instructions carefully. Working time of the mixed product, for intermediate storage at 0° – max 4° C, maximum 4 hours.   ...

Product Features Fuel resistant Ethanol resistant Temperature resistant up to 80°C Application: Before use, stir the TAPOX very well, add hardener & mix to a completely thin coating. Please note that TAPOX is a resin & not a paint & must, therefore, be stirred longer to obtain the completely thin mixture! Clean the tank very thoroughly before the internal coating, derust it & protect it against new corrosion with Fertan Rust Remover. Only apply the TAPOX coating in a completely dry tank. Follow the processing instructions carefully. Working time of the mixed product, for intermediate storage at 0° – max 4° C, maximum 4 hours.   ...