DINITROL 1000 is applied by spraying with manual or semi-automatic application equipment, & is suitable for either air-mix or airless spraying. Application temperature should be between 15 & 30°C.. •
Colour: Opal to beige transparent • Type of film: Waxy. • Density at 23°C: 830 kg/m³. • Viscosity at 23°C, DIN 4: 18 s • Dry matter content: 50% by weight. • Flash point: 40°C • Aromatic content in solvent: 90°C • Salt spray test: 500 h • Penetration 50 µm gap: > 30 mm
...

This kit

Includes:: an Under-body Coating Gun & a can of Dinitrol 3125HS (1L), a specially formulated wax

...

A specially formulated wax which penetrates rust & dirt preventing further corrosion. Use on open surfaces or cavities. Even damp & dirty surfaces will not affect its superb performance. Ideal for vertical surfaces, if you are planning on using on the inner chassis rails then please consider Dinitrol ML or 1000 as these products offer better creeping properties. To clean use white spirit or solvent & elbow grease. Not recommended to thin it down with anything. Steam clean the underneath of the vehicle & allow to dry, remove any flaking rust & mask up any areas where you do not want the wax to go, time consuming but well worth the effort as it is difficult to remove any unwanted overspray later. Treat any surface rust with the rust converter (3125HS), once it has turned black proceed to treat the cavities with the cavity wax also giving a fine coating of cavity wax to the underbody of the vehicle with any you have left over as it contains rust inhibitors. Leave overnight to dry & then apply the underbody coating (4941), this will dry to a leave a finger print in it type finish as it remains soft underneath so it can migrate & reseal itself when it gets a stone chip. When dry remove the masking & away you go. Don't forget to wear something you can throw away afterwards.   ...

Dinitrol 3125 HS is a specially formulated wax which penetrates rust & dirt preventing further corrosion. Use on open surfaces or cavities. Even damp & dirty surfaces will not affect its superb performance. Dinitrol 3125 HS will not crack, chip or peel & is designed for application to internal & external surfaces of cars, trucks & busses. The product is particularly suitable for use on old vehicles where corrosion is evident on e g the underbody. Ideal for vertical surfaces, if you are planning on using on the inner chassis rails then please consider Dinitrol ML or 1000 as these products offer better creeping properties. Severely attacked areas can be applied in combination with Dinitrol ML (S330) for greater effect. Available in 500ml (Aerosol) & 1 litre. Method of use: Dinitrol 3125 HS is applied by spraying with manual or semi-automatic application equipment, & is suitable for either airmixed or airless spraying. To clean use white spirit or solvent & elbow grease. Not recommended to thin it down with anything. Store in dry conditions away from other combustible materials, heat & direct sunlight. It should not be stored at a temperature above 30 deg C. If stored at low temperature the container should be held at a temperature of 15 to 25 deg C for 24 hours before use. Application temperature should be between 15 & 30 deg C. Application: Steam clean the underneath of the vehicle & allow to dry, remove any flaking rust & mask up any areas where you do not want the wax to go, time consuming but well worth the effort as it is difficult to remove any unwanted overspray later. Treat any surface rust with the rust converter, once it has turned black proceed to treat the cavities with the cavity wax also giving a fine coating of cavity wax to the underbody of the vehicle with any you have left over as it contains rust inhibitors. Leave overnight to dry & then apply the underbody coating (4941), this will dry to a leave a finger print in it type finish as it remains soft underneath so it can migrate & reseal itself when it gets a stone chip. When dry remove the masking & away you go   ...

Front valances & under wings are always subject to stone chips, give long term protection by spraying Stone Chip. Long-term protection products against corrosion & stone chipping with a synthetic resin/plastic basis. After drying, the materials are resistant to carbon hydride-based cold cleaning agents, surfactant-based acid & alkaline high pressure cleaners, salt water & road salt.

Colour: Black Available

Size: 500ml & 1L



...

DINITROL 4941 is a black solvent based underbody coating which resists corrosion & abrasion. The underbody coating product is widely used in the treatment of vehicles during production, at import plants & in aftermarket applications. When applied to a clean, dry surface, it adheres to both painted surfaces & those coated with a layer of PVC or similar material. Zinc, rubber & plastics are completely unharmed by the product. DINITROL 4941 / Car is also designed for use on spare parts, machines & iron & steel structures in highly corrosive environments. Apply over Dinitrol HS 3125 for the ultimate in rust prevention. To apply this product use Wax / Shutz Gun. Available in Aerosol (500ml) or 1 litre. ...

DINITROL 4941 is a black solvent based underbody coating which resists corrosion & abrasion. The underbody coating product is widely used in the treatment of vehicles during production, at import plants & in aftermarket applications. When applied to a clean, dry surface, it adheres to both painted surfaces & those coated with a layer of PVC or similar material. Zinc, rubber & plastics are completely unharmed by the product. DINITROL 4941 / Car is also designed for use on spare parts, machines & iron & steel structures in highly corrosive environments. Apply over Dinitrol HS 3125 for the ultimate in rust prevention. To apply this product use Wax / Shutz Gun. Available in Aerosol (500ml) or 1 litre. ...

The DINITROL 6030 Pyrmoplast Aluminium
- Metalised Body Filler came out as best budget buy in an independant survey into non pourous
...

Dinitrol 410UV Black Joint Sealer. After welding, you must always seal joints between panels properly, preventing future corrosion caused by moisture seeping into the joints. Dinitrol Joint Sealer is easy to apply with a standard caulk gun & dries within hours ready to paint. Caulking gun not included. DINITROL 410UV features
- One component polyurethane sealing & adhesive compound.
- Fast drying, elastic & can be over-painted. Immediate over-painting is possible
- wet on wet
- however, do not use paint with alcohol or alkyd-resin.
- Used for attaching plastic body panels, spoilers, body kit, scoops & vents to bodywork.
- UV resistant. Also available in White. * Product contains Isocyanates.





...

Dinitrol Converust RC900 forms an impenetrable barrier to oxygen & moisture. Ideal for cavities, panels & under-body work. Loose & flaking material should be removed but it is not necessary to clean down to bare metal. This Aerosol version of Dinitrol Converust RC800 converts rust to a stable organic iron compound. Dries to a hard black film ready for fillers or topcoats. 400ml aerosol. ...