Phobya High Density 60cm white warm (72x SMD LED´s) LED-Flexlight The ultimate modding highlight! Make your PC true eye-candy! With the use of the Phobya Flexlight strip it is now possible to shine a light into every corner of your enclosure with even more LEDs! The 4-Pin Molex extension loops through the required energy & hence still allows use of the PSU connector. For mounting the pre-applied adhesive tape at the back of the strips. Hence mounting of the Flexlights is easy to do in any spot in the enclosure. Many possibilities allow many different lighting effects: At the in- or outside of the enclosure, wrapped around the reservoir or simply put at the base of the enclosure. Thanks to the LED technology the Flexlights have an extremely low power consumption & barely any heat dissipation. in addition the Flexlight strip is watertight, giving many new possibilities in combination with a water cooling system. The Flexlights can even be hung into a reservoir for a completely new look! The great quality of manufacturing & advanced technology makes Flexlights the ultimate lighting solution! Of course shortening of the Flexlight strips is possible without problems, simply cut them to the desired length! Please note that the cut should only be made at the cut marks (every third LED), as the last LEDs will not functions otherwise. Even extension is possible for users with soldering experience. This even allows combination of Flexlights in different colours! New generation: The combination of the Tri Bright technology in combination with the closely spaced high-density LEDs allows extreme lighting power! Beautifully black sleeved allow this component to be integrated cleanly into high-end systems. Flexlights outside of the PC? Of course! Use Flexlights to illuminate a table from the bottom, a couch from the rear or even a photo frame! All of these beautiful possibilities can be realized with the Phobya external power supplies: No PC is required, no noisy fans are disturbing the silence. Simply order one of the Phobya PSUs (Item No. 84006 or 84011) & enter the world of endless lighting possibilities! Technical specifications: Length: 60cm

Colour: Warm white

Width: 10mm (strip only) Number of LEDs: 72 Voltage: 12VDC to 14VDC Connector: 4-Pin Molex



...

Phobya internal USB (Universal Serial Bus) connection cable 100cm
- black This cable is needed to connect a Mainboard USB (Universal
...

Phobya internal USB (Universal Serial Bus) connection cable 50cm
- black sleeve This cable is needed to connect a Mainboard USB
...

Phobya internal USB (Universal Serial Bus) extension 30cm
- black With this internal USB (Universal Serial Bus) 2.0 extension cable
...

Phobya LED-Flexlight RGB controller with IR-Remote controller Phobya's controller with remote controller, the interface for the Phobya RGB LED Flexlights. The Phobya RGB LED Flexlights offer many lighting possibilities, but they need a controller device which unleashes their potential. This is such a controller which offers everything which is needed for control of the RGB LED Flexlights. The Phobya controller is equipped with a voltage transformer with a repleacable 4-Pin Molex connector which can be used in all PC systems or alternatively with the external Phobya PSUs (Item No. 84006 or 84011). The Flexlights can be connected to one of the three fixed cables which each allw one Flexlight to be connected. Of course the controller also works if only one or two Flexlights are connected. The remote control send signals to the controller via infrared. The intuitive user interface shows the user exactly what happens when the buttons are pushed. The different base colours can be mixed to different colours by pushing the according buttons. in addition a dimmer is implemented to allow different levels of light intensity. Besides these basic functions automatic blinking modes can be activated to create a special lighting effect. Technical specifications: Inlet cable length: 40cm Outlet cable length: 20cm each

Colour: Black Power connector: 4-Pin Molex Number of RGB connectors: 3 Maximum current: 6A

...

Phobya NB-e Loop 1600rpm
- Bionic Fan The world's first high-tech compact fan with patented bionic Bionic Loop rotor comes from
...

Phobya NB-e Loop 1800rpm
- Bionic Lufter Black Edition The world's first high-tech compact fan with patented bionic Bionic Loop
...

Phobya SATA 3.0 connection cable angled with safety latch 60cm
- black Discription Connection cable between Mainboard & SATA devices.
...

Phobya temperature sensor in / outer thread G1/4 The new temperature sensor from Phobya with g 1/4" inner thread & G1/4" outer thread respectively. With its compact design this sensor can be integrated into the cooling loop at virtually any suitable thread. Its timeless design makes it blend right into the system, especially as it's low height of only 11, 6mm (without threads) allows it to fit below almost any connector. The sensor cable is equipped with a standard 2-Pin plug. High-Flow, no narrowing of the cooling channel inside of the sensor! Also see example of installation. Sleeving: This cable is not only practical, it is also optically appealing, The surrounding mesh, also called mesh, which is surrounding the cable itself offers the advantages that every Pro-modder is looking for: A completely unique look, even of the cables in the system! Special attention was paid to the combination of cable connectors, sleeve & heatshrink which were used to ensure great design & a unique as well as elegant look. Technical specifications: Connection threads: G1/4" Main body: Nickel plated brass Cover: Delrin Diameter: 23, 9mm Height with thread: 19, 7mm Thread length: 11mm Cable length: 50cm 1. Side: G1/4" outer thread 2. Side: G1/4" inner thread Connector plug: 2-Pin (Mainboard) Length of connecting cable: 50 cm Manufacturer: Phobya Thermal resistance (at 25 ° C): 10 k Ohm (Mainboard) ...

Phobya temperature sensor in / outer thread G1/4
- matte black The new temperature sensor from Phobya with g 1/4" inner thread
...