The Modular Power PSUs from Kolink boast an enhanced circuit design & an associated performance increase. These features offer a significant enhancement of voltage regulation & meet the needs of modern powerful computers. In addition, the extremely quiet 120mm fan, with a fined-tuned RPM curve, has been optimized for airflow. This makes the Modular Power the quietest power supply of its kind. The Modular Power PSUs looks amazing in any high-end gaming system due to its modern design & the flexible, flat & semi-modular cables use for connections across the system. Features 444W & 37A on a 12V rail 80 PLUS bronze certificate for high efficiency ATX form factor with a length of 160 mm Semi-modular cable management, modern look with flat black cables Connectors: 1x 24-pin, 1x 4+4-pin, 2x 6+2-pin, 4x SATA, 2x Molex Kolink Modular Power: Full performance & high efficiency The 500 Watt model of the Modular Power series offered here has enough connections & performance for fast gaming computers with basic equipment. The PSU delivers up to 444W & 37A on the +12V rail while providing 100W & 15A each on the +3.3V & +5V rails. This especially high efficiency meets the requirements of 80 Plus Bronze 230V EU & exceeds 85/82/82 percent at 50/20/100 percent load (at 230 Volt input voltage). The PSUs highly efficient circuit design features independent DC-to-DC converters for the 3.3V & 5V outputs, ensuring extremely precise voltage regulation. Each example of Modular Power series is cooled by a 120 mm fan with durable & quiet sleeve bearings that offer a fine-tuned RPM curve. Thanks to the optimized airflow, the fan & thus the entire PSU remain quiet as a whisper. Besides the 20+4 pin for the motherboard, the Kolink Modular Power has a 4+4 pin connector for the CPU & two 6+2 pin connectors for dedicated graphics cards. Four SATA & two Molex connectors are available for additional components. The flat, flexible, completely & semi-modular black cables have a modern look & fit into almost any up-to-date gaming setup. Note: For environmental reasons the manufacturer does not supply a power cord for connection to the mains. ...

The Modular Power PSUs from Kolink boast an enhanced circuit design & an associated performance increase. These features offer a significant enhancement of voltage regulation & meet the needs of modern powerful computers. In addition, the extremely quiet 120mm fan, with a fined-tuned RPM curve, has been optimized for airflow. This makes the Modular Power the quietest power supply of its kind. The Modular Power PSUs looks amazing in any high-end gaming system due to its modern design & the flexible, flat & semi-modular cables use for connections across the system. The 600 Watt model of the Modular Power series offered here has enough connections & performance for fast gaming computers with basic equipment. The PSU delivers up to 546W & 45.5A on the +12V rail while providing 100W & 15A each on the +3.3V & +5V rails. This especially high efficiency meets the requirements of 80 Plus Bronze 230V EU & exceeds 85/82/82 percent at 50/20/100 percent load (at 230 Volt input voltage). The PSUs highly efficient circuit design features independent DC-to-DC converters for the 3.3V & 5V outputs, ensuring extremely precise voltage regulation. Each example of Modular Power series is cooled by a 120 mm fan with durable & quiet sleeve bearings that offer a fine-tuned RPM curve. Thanks to the optimized airflow, the fan & thus the entire PSU remain quiet as a whisper. Besides the 20+4 pin for the motherboard, the Kolink Modular Power has a 4+4 pin connector for the CPU & two 6+2 pin connectors for dedicated graphics cards. Four SATA & two Molex connectors are available for additional components. The flat, flexible, completely black & semi-modular cables have a modern look & fit into almost any up-to-date gaming setup. Note: For environmental reasons the manufacturer does not supply a power cord for connection to the mains. Main Features 546W & 45.5A on a 12V rail 80 PLUS bronze certificate for high efficiency ATX form factor with a length of 160 mm Semi-modular cable management, modern look with flat black cables Connectors: 1x 24-pin, 1x 4+4-pin, 2x 6+2-pin, 4x SATA, 2x Molex ...

The Modular Power PSUs from Kolink boast an enhanced circuit design & an associated performance increase. These features offer a significant enhancement of voltage regulation & meet the needs of modern powerful computers. In addition, the extremely quiet 120mm fan, with a fined-tuned RPM curve, has been optimized for airflow. This makes the Modular Power the quietest power supply of its kind. The Modular Power PSUs looks amazing in any high-end gaming system due to its modern design & the flexible & flat cables use for connections across the system. Features 648W & 54A on a 12V rail 80 PLUS bronze certificate for high efficiency ATX form factor with a length of 160 mm Modern look with flat black cables Connectors: 1x 24-pin, 1x 4+4-pin, 4x 6+2-pin, 6x SATA & 2x Molex Kolink Modular Power: Full performance & high efficiency The 700 Watt model of the Modular Power series offered here has enough connections & performance for fast gaming computers with basic equipment. The PSU delivers up to 648W & 54A on the +12V rail while providing 110W & 15A each on the +3.3V & +5V rails. This especially high efficiency meets the requirements of 80 Plus Bronze 230V EU & exceeds 85/82/82 percent at 50/20/100 percent load (at 230 Volt input voltage). The PSUs highly efficient circuit design features independent DC-to-DC converters for the 3.3V & 5V outputs, ensuring extremely precise voltage regulation. Each example of Modular-Power series is cooled by a 120 mm fan with durable & quiet sleeve bearings that offer a fine-tuned RPM curve. Thanks to the optimized airflow, the fan & thus the entire PSU remain quiet as a whisper. Besides the 20+4 pin for the motherboard, the Kolink Modular Power has a 4+4 pin connector for the CPU & four 6+2 pin connectors for dedicated graphics cards. Six SATA & two Molex connectors are available for additional components. The flat, flexible & completely black cables have a modern look & fit into almost any up-to-date gaming setup. Note: For environmental reasons the manufacturer does not supply a power cord for connection to the mains. ...

Cutting a striking figure amongst the highly competitive ATX-format segment, the Nimbus Midi-Tower from Kolink offers an RGB-LED strip rounding the large cut-out in the front – enabling a significant improvement in airflow. The hardware installed inside the case will also remain clear of dust thanks to the filter, which is important as users will also enjoy the opportunity to admire their hard-earned hardware through the tempered glass side. In spite of Kolink’s use of solid tempered glass, the Kolink Nimbus still weighs only 4, 58 Kg. The generous

Dimensions of the case not only help with airflow, they also allow users to install motherboards up to ATX in form factor. Graphics cards up to 325 mm long are compatible - meaning that the case is perfect for housing some seriously high-end gaming hardware. The Features of the Kolink Nimbus Midi-Tower at a Glance Designer case in black for motherboards up to ATX Large air inlet in the front with RGB-LED surround for better airflow Magnetic dust filters on the front, roof and bottom 4 mm thick tempered glass side panel 1x Pre-installed 120 mm fan, 6 possible in total I/O Panel with 2x USB (Universal Serial Bus) 2.0 / 1x USB (Universal Serial Bus) 3.0 & HD Audio In/ Out, RGB-LED controller Support for radiators up to 240 mm in front & roof 2x 3, 5/2, 5“ drive slots, 2x slots for 2, 5” drives on motherboard tray Supports graphics cards up to 32, 5 cm long & CPU coolers up to 16 cm Tempered Glass Side Panel & Pre-Installed Fan The robust chassis consists of one millimetre thick SECC steel &

Includes:: a four millimetre thick tempered glass side panel, with an aluminium-look plastic front. A large cut-out in the front has a digitally addressable RGB-LED strip included which can be both synced to compatible motherboards & controlled on the front panel. The magnetic dust filter located behind it helps keep the interior clean & dust free & allows for sufficient airflow. The interior has a black coating & utilises a power supply shroud to help maintain a clean aesthetic. Beneath this, users will find a non-removable drive cage with brackets for two 3, 5- or 2, 5” drives as well as space for the power supply itself. Two additional slots for 2, 5“ drives are located to the rear of the motherboard tray. Dust Filters Keep the Kolink Nimbus Clean In order to keep your gaming hardware supplied with a continuous stream of cool, fresh air
- one (of a possible total of six) 120 mm fan in black is included with the case & installed in the rear. The front of the case supports up to three 120 mm fans, the roof of the case allows for two further 120 mm fans. The front of the case supports two 140 mm fans. A 240 mm radiator can be installed in the front & the roof. The motherboard tray and the PSU cover include various openings for all the cable management options you could ask for. The air inlets located in the roof and underside of the case also include a fine mesh. These are magnetic & utilise a honeycomb-structure design to add strength. Graphics cards up to 32, 5 cm with CPU coolers up to 16 cm are both supported. in addition, the I/O panel located on the front of the case
Includes: two USB 2.0 ports along with a USB 3.0 Type-A port. A switch for controlling the RGB lighting is also available.





...

Combining performance & affordability, the Kolink Observatory Lite Midi-Tower is a perfect mix of features & functionality. With no less than 4 a RGB LED 12cm fans included as standard, controlled with a supplied remote which allows a variety of modes, lighting options & even speed control, the Observatory Lite also provides a stylish tempered glass front panel with ample side ventilation. The hardware you choose to install is also key; the tempered glass side panel means that you can create a showstopping system build. All in all the Observatory Lite is an extremely strong chassis with plenty to offer. THE FEATURES OF THE KOLINK OBSERVATORY LITE AT A GLANCE Tempered Glass front panel with 3 x pre-installed 12cm a RGB LED fans Tempered glass side panel for unobstructed view of the interior Designed for ATX-/ Micro-ATX-/ Mini-ITX motherboards RGB controller hub with remote control allowing various lighting modes & effects, plus fan speed control Option to sync to motherboard software provided as standard Pre-installed rear 120mm fan with digitally addressable RGB lighting Support for radiators up to 280mm in the front I/O Panel with 1x USB (Universal Serial Bus) 3.0 & 2x USB (Universal Serial Bus) 2.0, HD Audio, RGB-LED controller PSU shroud with air inlets for a cleaner look Graphics cards up to 335 mm supported, CPU coolers up to 160 mm, PSUs up to 180 mm KOLINK OBSERVATORY LITE: FORM & FUNCTION IN ABUNDANCE The digitally addressable RGB-LED fans, 4 of which are preinstalled, are controlled by the supplied remote & RGB hub. Alternatively, the fans can be hooked up & controlled using a compatible motherboard thanks to its use of a standard 3-pin (5VDG) connector. The tempered glass side panel allows users to enjoy a panoramic view of the lighting used inside the Kolink Observatory Lite. Aside from the pre-installed fans, users are also free to install two more 120mm fans in the roof. This is where a magnetic dust filter can be found installed on the honeycomb-style mesh. The side-facing air inlets on the front & in the PSU shroud also contribute to the excellent airflow of the case. Users are also free to install a 280 mm radiator in the front. THE KOLINK OBSERVATORY LITE: HARDWARE FOCUSSED The interior comes entirely in black, with a PSU shroud that only adds to the sleek & unobtrusive look. Behind the shroud is where users will find space for a pair of 3.5& Prime; HDDs in the HDD cage provided, which also has anti-vibration mountings. Alternatively, 2.5& Prime; SSDs can be installed here, or next to the motherboard. The motherboard tray & PSU shroud both offer numerous openings for optimum cable management, with up to 30mm cable management space. Underneath the case is a removable dust filter appropriate to an ATX-form factor PSU, which can itself be up to 18 cm in length. Graphics cards can be up to 33.5cm long (31cm if mounting an AIO) & CPU coolers up to 16 cm tall. in addition, the I/O panel located at the front possesses two USB (Universal Serial Bus) 2.0 ports as well as an USB (Universal Serial Bus) 3.0 Type-A port. ...

Kolink is pleased to introduce the incredibly stylish Observatory Midi-Tower with its fantastic tempered glass side panel & transparent front. The inclusion of a total of four pre-installed RGB-LED fans allows the case to unlock its full cooling potential. The lighting can also be controlled via the included controller & remote control. The Observatorys spacious interior offers capacity for a wide range of hardware & components. Some of the highlights of this case include pre-installed dust filters, extensive space for watercooling as well as practical cable management options. These are just some of the strong points of this case, & all that in spite of the extremely competitive price point. The Features of the Kolink Observatory at a Glance Case designed for motherboards up to E-ATX 4 mm tempered glass side & front panel 4x 120 mm flowing addressable RGB ring fans including controller & remote I/O panel with 2x USB (Universal Serial Bus) 2.0 / 1x USB (Universal Serial Bus) 3.0 & HD Audio In/ Out Support for two 240 mm radiators 3x 3.5/2.5" drive slots Graphics cards up to 38 cm long & CPU coolers up to 16 cm in height Tempered Glass Side/ Front Panel & Four Pre-Installed RGB Fans The robust chassis consists of one millimetre strong SECC steel & is equipped with a four millimetre thick tempered glass side & front panel. The interior interior has a black coating & is also kitted out with a shroud for the power supply to ensure an incredible clean look. There is also a hard drive cage with brackets for three 3.5- or 2.5-" drives. The visual highlights of the case include three 120 mm fans pre-installed in the front & an additional fan in the back. The fans come with 16 individually addressable RGB-LEDs. Their lighting can be controlled by the bundled RGB controller & fan hub which can be placed in a location of your choosing as well as the infrared remote control. This means that you can choose from over 300 dynamic lighting effects! Two further 120 mm fans can be mounted in the top. Dust Filters Keep the Kolink Observatory Clean The motherboard tray & the power supply shroud offer numerous cable openings. A 240 mm radiator can be installed in the front & the top of the Observatory case. The cases air vents come equipped with fine dust filters that are located in the top & underside of the case. These can be removed without the need for tools & even come complete with a smart honeycomb design. Graphics cards up to 38 cm long & CPU coolers up to 16 cm high are compatible. Furthermore the I/O panel located on the front also comes with two further USB (Universal Serial Bus) 2.0 connectors as well as a USB (Universal Serial Bus) 3.0 Type A port. There is also a slot for a USB (Universal Serial Bus) Type C connection, but this is not included in the case & must be retrofitted separately. The same applies to a switch for controlling the RGB lighting on the I/O panel. ...

Kolink is pleased to introduce the incredibly stylish Observatory Midi-Tower with its fantastic tempered glass side panel & transparent front. The inclusion of a total of four pre-installed RGB-LED fans allows the case to unlock its full cooling potential. The lighting can also be controlled via the included controller & remote control. The Observatorys spacious interior offers capacity for a wide range of hardware & components. Some of the highlights of this case include pre-installed dust filters, extensive space for watercooling as well as practical cable management options. This edition of the Observatory is available in White, with a white interior to match. These are just some of the strong points of this case, & all that in spite of the extremely competitive price point. The Features of the Kolink Observatory at a Glance Case designed for motherboards up to E-ATX 4 mm tempered glass side & front panel White Chassis & white interior 4x 120 mm flowing addressable RGB ring fans including controller & remote I/O panel with 2x USB (Universal Serial Bus) 2.0 / 1x USB (Universal Serial Bus) 3.0 & HD Audio In/ Out Support for two 240 mm radiators 3x 3.5/2.5" drive slots, plus 2 x 2.5" bracket for the rear of the motherboard Graphics cards up to 38 cm long & CPU coolers up to 16 cm in height Tempered Glass Side/ Front Panel & Four Pre-Installed RGB Fans The robust chassis consists of one millimetre strong SECC steel & is equipped with a four millimetre thick tempered glass side & front panel. The interior interior has a black coating & is also kitted out with a shroud for the power supply to ensure an incredible clean look. There is also a hard drive cage with brackets for three 3.5- or 2.5-" drives, along with a bracket for the rear of the motherboard that can fit an additional 2 x 2.5" drives. The visual highlights of the case include three 120 mm fans pre-installed in the front & an additional fan in the back. The fans come with 16 individually addressable RGB-LEDs. Their lighting can be controlled by the bundled RGB controller & fan hub which can be placed in a location of your choosing as well as the infrared remote control. This means that you can choose from over 300 dynamic lighting effects! Two further 120 mm fans can be mounted in the top. Dust Filters Keep the Kolink Observatory Clean The motherboard tray & the power supply shroud offer numerous cable openings. A 240 mm radiator can be installed in the front & the top of the Observatory case. The cases air vents come equipped with fine dust filters that are located in the top & underside of the case. These can be removed without the need for tools & even come complete with a smart honeycomb design. Graphics cards up to 38 cm long & CPU coolers up to 16 cm high are compatible. Furthermore the I/O panel located on the front also comes with two further USB (Universal Serial Bus) 2.0 connectors as well as a USB (Universal Serial Bus) 3.0 Type A port. There is also a slot for a USB (Universal Serial Bus) Type C connection, but this is not included in the case & must be retrofitted separately. The same applies to a switch for controlling the RGB lighting on the I/O panel. ...

With their premium & yet affordable gaming cases, Kolink has firmly established themselves as a leader in the world of respected case manufacturers. The Outline represents an impressive addition to their category of high-performance cases, one that manages to offer as much in terms of design as it does in functionality. The spacious interior fits up to a high-end SSI-EEB motherboard & graphics cards up to 360 mm in length. The cards can also be installed vertically, providing they are dual slot width, using the supplied mount & a PCI-E riser cable (sold separately). It goes without saying that the case offers plenty of room for all your cooling needs: the front supports a radiator up to 360 mm & the roof supports a 240 mm radiator. What really stands out however is the design of its front panel: on the left are functional but attractive air inlets in a checkerboard pattern, on the right is a digitally addressable RGB-LED strip in the form of a narrow rectangle. A pre-installed high-performance 120 mm ARGB fan illuminates the interior of this deceptively large Midi-Tower, meaning that excellent cooling is a given. A tempered glass side panel allows users to enjoy an unobstructed view of the installed hardware. Features Stylish Midi-Tower for motherboards up to SSI-EEB format Tempered glass side panel for a clear view of the interior Digitally addressable RGB-LED strip on the front Option of vertically mounting a dual slot GPU Radiator up to 360 mm on the front, up to 240 mm on the roof A pre-installed 120mm fan on the back with digitally addressable RGB-LEDs Up to six 120 mm fans supported Space for graphics cards up to 360 mm, CPU coolers up to 162 mm I/O Panel with controller for RGB-LEDs, 1x USB (Universal Serial Bus) 3.0, 2x USB (Universal Serial Bus) 2.0 & HD Audio Plenty of Space for Gaming Hardware in the Kolink Outline Even if the outside of the case corresponds to the

Dimensions of a Midi-Tower, the Kolink Outline manages to provide support for motherboards up to the SSI-EEB format. Even graphics cards up to 360 mm will fit, thanks to the amount of room available behind the front panel. Even large CPU coolers up to 162 mm in height will fit with ease. A shroud helpfully conceals the power supply & the HDD cage, in which users can either install two 3.5"- or two 2.5" drives. The rear of the motherboard allows for two 2.5" SSDs to be installed. Those preferring to opt for air cooling will appreciate the number of mounting points present for 120 mm fans. The roof supports two 120 mm fans. It is also equipped with a handy mesh, which allows air to flow through the case, without excess dust thanks to the presence of a dust filter. The result is that this is a large, attractive yet low-maintenance case. If thats still not enough cooling, the front supports up to three 120 mm fans. The slot at the rear is occupied by a 120 mm fan. The pre-installed fan is equipped with digitally addressable RGB-LED lighting. Of course, users are free to install radiators instead of fans if needed, with a 240 mm radiator in the roof & a 360 mm at the front. Tempered Glass & RGB-LEDs to Put Your Hardware On Show The power supply cover provides a tidy look inside the case. Well-placed feedthroughs & cable guides allow for sophisticated cable management. The eye-catching strip on the front of the case is equipped with digitally addressable RGB LEDs, the lighting of which can be controlled via a switch on the I/O panel, or the strip can be connected directly to a motherboard & controlled directly via the board instead. The lighting on the pre-installed fan is also done via a compatible 3-pin connector (5VDG), which can also be controlled via the controller on the I/O panel or via the motherboard. The RGB switch on the I/O panel can also double up as a reset button. In addition to the RGB/ Reset switch, there are one USB (Universal Serial Bus) 3.0 & two USB (Universal Serial Bus) 2.0 slots as well as 3.5 millimetre sockets for headphones & microphone, a power LED & an HDD LED.

...

The Phalanx Midi-Tower builds on Kolinks case line-up with a stylish new d RGB-LED model complete with a tempered glass side panel & a brushed aluminium front as well as a mesh cut-out. It is defined by a strikingly attractive design that is paired with a multitude of mounting options for fans, water-cooling & storage devices. The interior of the black Phalanx is as capacious as it is stylish. Designer case in black for motherboards up to E-ATX Tempered glass side panel & front with mesh cut-out Four pre-installed digitally addressable 120 mm d RGB fans, 6 possible in total I/O Panel with 2x USB (Universal Serial Bus) 2.0 / 1x USB (Universal Serial Bus) 3.0 & HD Audio In/ Out Supports three radiators in 120-mm-, 240- & 280 mm formats 2x 3, 5 or 3x 2, 5" storage mounts Supports graphics cards up to 37 cm long & CPU coolers 16 cm tall ...

The Phalanx V2 Midi-Tower builds on Kolinks case line-up with a stylish new d RGB-LED model complete with a tempered glass side panel & a brushed aluminium front with a mesh cut-out. Four 120mm PWM fans with d RGB illumination are pre-installed. These look particularly stylish set against the dark black of the Phalanx V2s stylish interior. A bundled hub allows for control of the fans speed & illumination, either directly via the motherboard or the (also bundled) remote control. Overall these features & the Phalanx V2s striking & attractive design make for an outstanding case that can be paired with a multitude of mounting options for fans, watercooling & storage devices. Features Designer case in black for motherboards up to E-ATX Tempered glass side panel & front with mesh cut-out Four pre-installed digitally addressable 120 mm PWM Dual Ring d RGB fans, 6 possible in total I/O Panel with 2x USB (Universal Serial Bus) 2.0 / 1x USB (Universal Serial Bus) 3.0 & HD Audio In/ Out Supports three radiators in 120-mm-, 240- & 280 mm formats 2x 3.5 or 4x 2.5& Prime; storage mounts Supports graphics cards up to 37 cm long & CPU coolers 16 cm tall ARGB motherboard control using Asus, MSI & Asrock motherboards Included adapter cable to connect ARGB controller to Gigabyte motherboards Four pre-installed PWM Dual Ring d RGB Fans & Tempered Glass Side: Equipped with 7 PCI slots, the chassis of the Kolink Phalanx V2 consists of steel & the left side bears an attractive tempered glass window. This is not just attached with screws; it folds out conveniently thanks to two hinges. The lower section is completely covered by a shroud that helps conceal the PSU & any less-than-elegant cabling. The two 3, 5- or 2, 5& Prime; drive bays are also located here. There is also space for a further 2 x 2.5& Prime; drives on the rear of the case using the predrilled holes. To ensure excellent airflow, the case offers four pre-installed 120mm PWM fans with digitally addressable d RGB-LED lighting, as well as mesh strips in the front of the case. Three fans are installed in the front of the case, meaning they are visible through the mesh at the front. One is located in the back. All fans are connected to the included fan hub/RGB controller. The fans feature 8 LEDs on the inner edge & 16 on the outer edge. This enables them to generate multiple eye-catching & impressive effects. in addition, the d RGB lighting can be controlled using the bundled remote control, the reset switch on the I/O panel, or via the motherboard directly. The top of the case allows for two additional 120 mm- or 140 mm fans. For those who generally prefer larger fans, the case supports the installation of three 140 mm fans at the front in place of 120 mm fans should you prefer. Ingenious Interior Design The cleverly placed openings in the motherboard tray enable some exceptionally clean & tidy cable management. If users wish, the front- & top of the case are both capable of holding a radiator up to 280 mm in size. The back of the case naturally also holds a 120 mm radiator if needed. In order to protect the cases interior & your hard-earned components from dust, the case

Includes:: magnetic fan filters in the top, bottom & front. This makes them a breeze to remove & clean. Graphics cards up to 37 cm in length & CPU coolers up to 16 cm tall will fit this case. Power supplies can be up to 24 cm long. The I/O panel is located on the top of the Kolink Phalanx V2 & provides Audio-In/ Out, a USB (Universal Serial Bus) 3.0 port & two USB (Universal Serial Bus) 2.0 connectors. Also present is a dedicated button to cycle through illumination modes when it is connect to the d RGB hub. (Although it is also possible to connected the hub to the motherboard & either control the illumination via software or the included remote control.) The hub itself offers ten connectors for 6-pin fans with digitally addressable LED lighting. Moreover, there are two connectors for use with LED strips with 5VDG connections in the shape of a 4-pin connector. Also a bundled adapter enables users to connect the controller to Gigabyte motherboards in addition to motherboards from MSI & Asus.

...