Key Features Supports four Gigabit Ethernet WAN Ports USB (Universal Serial Bus) 3G/4G/LTE modem can also be added Wireless Management of up to 30 Dray Tek APs IPv 6/IPv 4 Dual-Stack High performance
- up to 500 Mb/s firewall throughput The Vigor 3220 is a router/firewall with four Gigabit Ethernet WAN ports, providing load balancing or failover for up to four WAN connections of any type. The Vigor 3220 is based on Dray Teks own Dray OS operating system, providing familiarity for users of other existing Dray Tek products. Robust & Comprehensive Firewall Security is always taken seriously with Dray Tek routers. The firewall protects against attacks including Do S (Denial of Service) attacks, IP-based attacks & access by unauthorised remote systems. Wireless, Ethernet & VPN are also protected by various protection systems. The Dray Tek object-based firewall allows even more setup flexibility than ever, enabling you to create combinations of users, rules & restrictions to suit multi-departmental organisations. The Vigor 3220 now also allows selective direction firewall rules of LAN to WAN, WAN to LAN or LAN to VPN. In addition, Qo S (Quality of Service Assurance) can now be selectively applied to specific users. High Availability For mission critical applications, a pair of Vigor 3220s can be set up in high-availability mode
- also known as hardware failover. This removes the Vigor 3220 as a single point of failure if it ceases operation or is damaged
- the standby router takes over operations. IPv 6
- Next Generation Internet Routing The Vigor 3220 supports IPv 6
- the successor to the current IPv 4 addressing system that has been used since the Internet was first created. IPv 4 address space is full up & IPv 6 allows for much more efficient routing & a larger address space. IPv 6 is supported both from your own ISP, but if your ISP does not (yet) support IPv 6, the Vigor 3220 also supports IPv 6 broker/tunnel services to provide IPv 6 access using either TSPC or AICCU via 3rd party IPv 6 providers. Web Content Filtering The content control features of the Vigor 3220 means that you can set restrictions on web site access, blocking download of certain file or data types, blocking specific web sites with whitelists or blacklists, blocking IM/P2P applications or other potentially harmful or wasteful content. Restrictions can be per user, per PC or universal. Using Dray Teks Global View service, you can block whole categories of web sites (e.g. gambling, adult sites etc.), subject to an annual subscription to the Cyren Globalview service, which is continuously updated with new or changed site categorisations or sites which have become compromised (such as infected with Malware). A free 30-day trial is included with your new router.




...

Key Features Five Gigabit WAN ports (4 x Ethernet & 1 SFP) Up to 50 WAN ports with optional Switch WAN Load Balancing & WAN Failover High-Availability (with CARP) Up to 500 simultaneous IPSec/PPTP/L2TP Tunnels The Vigor 3900 is a high-performance quad-Gigabit WAN router for high-performance applications including remote access, firewalling, load-balancing & failover. Its WAN throughput runs at up to 1 Gb/s, adequate for the most demanding SME applications. The WAN ports on the Vigor 3900 can provide load balancing or WAN failover. Based on a new Dray Tek OS platform, the Vigor 3900 combines high performance & capacity with Dray Teks traditional ease of use & comprehensive features set. For multi-tenant or departmental flexibility, the Vigor 3900 will support multiple LAN IP subnets, together with VLAN capabilities & user management, providing access to WAN resources only to the appropriate users or departments, as well as maintaining infrastructure effciency. Four WAN ports for load-balancing or failover Four Gigabit Ethernet WAN ports & one SFP slot (for fibre modules or an additional Ethernet module) provide 5 independent WAN ports for either load-balancing or failover applications. Gigabit Ethernet & SFP LAN Interfaces provide high speed connectivity to your LAN. Fibre is of particular use for longer distance deliveries, beyond the range of standard Ethernet, or where copper connections cannot be used. WAN Load-balancing weight or traffic-type rules can be set or on an automatic basis to spread WAN traffic evenly across all interfaces on a best-endeavour basis. Firewall The Vigor 3900s firewall is fully stateful, with a flowtrack mechanism & comprehensive WAN defences, including Do S/DDo S protection & flexible IP packet filtering. On the content side, the Vigor 3900 has several methods of content filtering to control user access to the web to keep their access appropriate, safe & productive. That helps keep your network efficient, your data secure & your online productivity high. Qo S Extensive Qo S facilities allow for efficient local traffic handling, ensuring that critical traffic is given the appropriate priority & that your network topology handles data in the most efficient way to help avoid congestion & bottlenecks. WAN traffic can be assigned one of 7 different priority levels for egress & 2 levels for ingress. Bandwidth can be reserved for critical applications.. Rules can be based on service type, users or IP source/desintations. VPN As a VPN endpoint/concentrator, the Vigor 3900 will support up to 500 simultaneous teleworker or LAN-to-LAN VPNs with a VPN throughput of up to 700 Mb/s, thanks to its hardware-based VPN co-processor. VPN security

Includes:: certificate, MOTP or token/PSK based access & key-hash authentication to ensure maximum security.

...

Powerful Enterprise Internet Gateway Featuring a Quad-Core Processor, the Vigor 3910 readily meets the needs of demanding networks, with over 9 Gb/s NAT throughput delivered through its 10 Gb E & 2.5 Gb E ports. Benefits: Full potential of the Internet. Flexible application. High-Performance VPN Concentrator The Vigor 3910 is ideal VPN Concentrator, providing over 3 Gb/s of IPsec performance & 1 Gb/s SSL VPN performance. Connect up to 500 IPsec & 200 SSL VPN tunnels simultaneously. Benefits: No bottlenecks. Affordable high performance. Flexible WAN Architecture Spread the load across up to 8 WAN links with Load Balancing. Policy-based Routing enables intelligent & flexible failover, for reliable & resilient connectivity. Benefits: Broadband Aggregation. Business continuity. Switchable WAN & LAN Ports 12 physical ports with 4 dedicated LAN ports & 8 switchable LAN or WAN ports. Allowing for up to 11 LAN ports in total, or Load Balancing up to 8 WAN connections. Benefits: Customisable to suit your network requirements. High Availability Provide hardware redundancy to mission critical applications with the installation of a second Vigor 3910. The backup autonomously resumes connections in the event of hardware failover. Benefits: Prevent a single point of failure. Maximum uptime. Manage Multiple Networks Create up to 50 VLANs, port-based or tag-based. Each fully configurable for NAT or Routing, sharing resources between networks or isolated from each other. Benefits: Easily secure & segment your networks. The Vigor 3910 is a Multi-WAN VPN Router designed for high performance & capable of handling the requirements of large & complex networks, with applications including Remote Access, Firewalling, Load-Balancing & Failover. Featuring 12 LAN & WAN interfaces in total, 4 dedicated LAN ports & 8 switchable ports that can operate as LAN or WAN ports to fit your network requirements. With up to 9 Gb/s of NAT & Firewall throughput, the Vigor 3910 is suitable for the most demanding & bandwidth intensive SME applications. Each of the WAN ports on the Vigor 3910 can be grouped together to provide Load Balancing or operate as Failover or Backup WAN connections. Based on the familiar Dray OS platform, the Vigor 3910 combines high performance & capacity with Dray Teks traditional ease of use & comprehensive feature set. For multi-tenant or departmental flexibility, the Vigor 3910 will support multiple LAN IP subnets, together with VLAN capabilities & user management, providing access to WAN resources only to the appropriate users or departments, as well as maintaining infrastructure efficiency. ...

The Dray Tek Vigor 3912 series is a premium next generation multi-WAN router making it ideal for your most demanding & complex networks. This VPN concentration is the evolution of our powerful 3910 model with even faster hardware to solve your large network challenges. ...

The Dray Tek Vigor AP-710 is a standalone wireless access point, ideal for adding wireless connectivity to an existing LAN, or for expanding the range of an existing wireless LAN by using the WDS features. As an access point, the Vigor AP-710 connects to your existing ethernet switch or router. Wireless users can then connect to your LAN. You can restrict access to specific devices by locking in their hardware MAC address & if you have a radius server, user access can be further limited requiring unique login using 802.1x authentication (MD5/PEAP mode). Where you wish to provide wireless access over a larger area, or throughout a larger building, you could install several AP-710s, each wired back to your central network. The AP-710 also supports limited functions within Dray Teks Wireless management system. In addition, the AP-710 can operate in several other wireless modes: Access Point
- Standard Operation, as described above Universal Repeater
- The AP-710 acts as both a wireless client & access point simultaneously, effectively increasing the range of an existing access point. Bridge
- Using two AP-710s, each connected to a separate wired LAN, a wireless bridge can be formed connecting the two LANs. Ideal where a physical link (cable) isnt possible, for example, across a road.


...

The Dray Tek Vigor AP-810 is a standalone wireless access point, ideal for adding wireless connectivity to an existing LAN, or for expanding the range of an existing wireless LAN by using the WDS features. It can also be used as part of the Dray Tek managed wireless system. The AP-810 replaces our popular AP-800 model, adding full compatibility with our managed wireless platform. Wireless Security The AP-810 features multiple levels of wireless security. Encryption using WEP, WPA, WPA2 (802.11i) is available you can also use the access control list (ACL) to specify the hardware addresses of clients which are permitted to connect (by MAC hardware address). Any unauthorised hardware is refused access. For additional user authentication, you can activate 802.1x RADIUS (Remote Authentication Dial-in User Service) which means that you can centrally manage & store user names & passwords either within the AP-810 setup itself (thus not needing any external server) on an external radius server which can permit time limited, temporary or continuous access to your clients as required. The Vigor AP-810 supports the 802.1q VLAN protocol so that if it is connected to an 802.1q enabled LAN, it can split tagged data (whether its different subnets or intended for different users) & broadcast each on its own SSID. This means, for example, that your guest Wi Fi access is provided on a separate isolated SSID with no access to your company data/devices. USB (Universal Serial Bus) Printer Port The AP-810 has a USB (Universal Serial Bus) interface into which you can connect a regular printer. That printer is then accessible from any wireless or wired PC which connects to the AP-810, or a PC anywhere else on the network to whick the AP-810 is connected. This is ideal to provide printer access to wireless laptops but could also be used for installing a printer elsewhere in your home/office by using a pair of AP-810s to make a bridge. WMM
- Wi Fi Multimedia The AP-810 implements intelligent wireless traffic prioritization for the most efficient management of wireless traffic by using the Wi-Fi Multimedia standard (WMM). WMM defines Quality of Service (Qo S) in Wi-Fi networks. It is a precursor to the upcoming IEEE 802.11e WLAN Qo S standard, intended to improve timing critical applications such as audio, video & voice applications over Wi Fi. WMM adds prioritized capabilities to Wi-Fi networks & optimizes their performance when multiple concurrent applications, each with different latency & throughput requirements, compete for network resources. WPS
- Wi Fi Protected Setup Wireless Security (encryption) is important to protect your data (privacy) but also to prevent unauthorised people from accessing your network or your Internet connection. The WPS system means that instead of having to create & enter long encryption keys, you can activate WPS registration. To activate, you press & hold the WPS button, then activate the WPS function on your PC; the two devices then automatically exchange encryption keys. For security, WPS an be disabled if the AP-810 is physically accessible. The same button on the AP-810 also serves as a physical on/off switch for the Wireless LAN if you wish to quickly disable it at any time, whilst still leaving your wired ports active.

...

The Dray Tek Vigor AP-910c is a wireless access point which can be operated in standalone or centrally managed/monitored mode (with the use of a central Dray Tek management product
- see later). The AP-910c is a high

Specification professional access point providing reliable & flexible coverage to all manner of applications. A vast array of security & management features helps the AP-910c improve & protect flexibility & integrity of your wireless LAN. The Vigor AP-910c is ideal for adding wireless connectivity to an existing LAN, or for expanding the range of an existing wireless LAN by using the WDS repeater features. The ceiling format of the unit means that it can provide unobstructed coverage to the area around it & aesthetically blends into any home or office environment thanks to its shape, size & hidden cable entry. The AP-910c can also be wall mounted. For ceiling mounting, a circular mounting plate (included with the unit) is fitted & then the AP-910c is attached. The AP-910c can be used together with our other access points (AP-710, AP-810 & AP-910c). For suspended ceilings, additional mounts are included to attatch the the ceiling T-Bars Simultaneous Dual-Band Operation & Extended 5 Ghz Bands The Vigor AP-910c supports simultaneous operation of the common 2.4 Ghz band & the new 5 Ghz b&. The 5 Ghz band is far less congested so if your PCs or other devices support the 5 Ghz b&, you can use that. The Vigor AP-910c operates both bands at the same time, so your devices can use either band & each has its own bandwidth so overall wireless capacity is also increased. The 5 Ghz supports the full range of extended domestic 5 Ghz channels, due to its support for DFS/TPC. You can select all 5 Ghz channels up to channel 140, as opposed to just the 4 Band A-Lower channels (which provides only two non-overlapping channels @ 80 Mhz channel width). Mounting & Coverage The AP-910c is designed to be installed on ceilings in order to serve the area below it. The cables (Ethernet or Power) can reach the AP-910c from the rear or the side. For solid ceiling fixing a backplate is supplied. The backplate fixes to the ceiling & the AP-910c then clips in. Alternatively, T-Bar mounts enable quick & easy attachments to suspended ceilings (see photo below). The AP-910c can also be wall-mounted
- keyhole slots on the back allowing any orientation.



...

Mesh Wireless Mesh Wireless links Vigor AP access points across both Wi-Fi & Wired links to cover a large area with a single Wireless network, spanning multiple Wireless Access Points & easily managed from the Mesh Root Vigor AP or with the Dray Tek Wireless app. The Mesh Root Vigor AP links up to your existing Internet router, such as the Dray Tek Vigor 2862ac & additional Vigor A Ps join up as Mesh Nodes, which connect wirelessly to the Mesh Root. Your devices see a single Wi-Fi network (SSID) & connect to the nearest Vigor AP in the Mesh, instead of a distant Wi-Fi network with low signal. Internet connectivity relays through the Mesh, using the up to 866 Mbps 5 G Hz wireless as the backhaul link, to relay between Mesh Nodes & avoid long waits for downloads. One of the Vigor AP 1000C's 5 G Hz 802.11ac radios can be dedicated as a Mesh backhaul. Providing higher performance & capacity for Mesh networks spanning multiple hops & managing more clients. Easy Setup with the Dray Tek Wireless App Dray Tek's Wireless app assists you with setting up Vigor AP 1000C access points & a Mesh Wireless network. Once installed on your Smartphone or Tablet, use the Quick Start Wizard to set your Vigor A Ps to operate as a Mesh Wireless network. Set up a single Vigor AP 1000C as a st&-alone Access Point, or extend an existing wireless network as a Range Extender. Simply scan the access point’s QR code to detect it, or manually input the Vigor A Ps default SSID & password, then configure your wireless network with step-by-step guidance. When it’s all set up, view the Mesh Wireless status & connected wireless clients from the app. 2 Gigabit Ports with Power-Over-Ethernet The Vigor AP 1000C has built-in Po E+ (Standard IEEE 802.3at Power over Ethernet) as standard. Connect the Vigor AP to a Po E+ Ethernet switch or Po E+ injector to power it without local power to the unit (power supply)
- the Vigor AP 1000C will take its power from the Ethernet cable. The Vigor AP 1000C supports Gigabit Po E (if you have a Gigabit Po E switch/injector) such as our Vigor Switch P1280 or P1092 models (or any other 802.3at device). Po E is ideal for situations where you do not have mains power available in the exact location where you want to install the Vigor AP 1000C or just for general aesthetic neatness, perhaps where the AP is installed somewhere prominent. The second Gigabit LAN port can be used to connect an additional device such as a camera or network switch to the Vigor AP. When the Vigor AP is operating in Mesh mode, the LAN ports are bridged to the wireless network, to connect additional devices into the Mesh network. The Dray Tek Vigor AP 1000C can alternatively be powered by an AC/DC mains PSU, for installations where you are not using Po E. Ceiling Mounting For ceiling mounting, a mounting plate (included with the unit) is fitted & then the Vigor AP 1000C is secured into place by sliding the Vigor AP into the mounting plate. Once installed, the AP is held securely in place. The AP-1000C is designed to be installed on ceilings in order to serve the area below it. The cables (Ethernet or Power) can reach the AP-1000C from the rear or the side. For solid ceiling fixing a backplate is supplied. The backplate affixes to the ceiling & the AP-1000C then clips in. Tri-Band 11ac Wave 2 Access Point The Vigor AP 1000C is an 802.11ac Wave 2 access point, improving performance by increasing the amount of data that can be sent at one time. 11ac Wave 2 uses MU-MIMO (Multi-User Multiple In, Multiple Out) technology to boost performance & capacity, building upon the Single-User (SU-MIMO) technologies introduced with 802.11n. The Vigor AP's MU-MIMO technology when used with MU-MIMO capable wireless clients, allows each antenna (or Spatial Stream) to send to separate wireless clients at the same time, potentially doubling the data transmission rate to clients. A typical wireless access point can send data to only one client at a time with its radio. With enough users connected, congestion slows down transfer speeds more & more, as the AP is shared between more clients. This can be particularly useful in locations with many phones, tablet & laptops connecting, where the Vigor AP's more efficient transmissions could allow each access point to serve more clients than an 802.11ac Wave 1 or 802.11n access point. Wireless Optimisation Dray Tek's Vigor AP access points have many features designed to improve wireless performance on your network, to ensure that every wireless client gets the best possible experience. Wireless Security & VLANs The Vigor AP 1000C features multiple levels of wireless security. Encryption using WPA2 / WPA3 is available & you can also use the access control list (ACL) to specify the hardware addresses of clients which are permitted to connect (by MAC hardware address). Any unauthorised hardware is refused access. For additional user authentication, you can have the Vigor AP 1000C authenticate clients with an 802.1x RADIUS (Remote Authentication Dial-in User Service) server, or use its internal RADIUS server. The Vigor AP 1000C supports the 802.1q VLAN protocol so that if it is connected to an 802.1q enabled LAN, it can split tagged data (whether it's different subnets or intended for different users) & broadcast each on its own SSID. This means, for example, that your guest Wi Fi access is provided on a separate isolated SSID with no access to your company data. Multi-SSID Over Mesh Dray Tek's Mesh system supports 802.1q VLAN tagging for its multiple Wireless networks (or SSIDs), over both wireless & wired Mesh links between Vigor A Ps. Each SSID provided by the Mesh network can have a VLAN tag assigned to it. VLAN tags are interpreted by the network's router & switch (es) to segregate one network from another. For instance keeping devices connecting to a guest network separate from resources on the private, internal network. Setting up a Mesh network to work with VLANs only requires setting up the Mesh Root with the VLAN tags on its SSIDs. This change propagates to Mesh Nodes when syncing the configuration between access points & Multi-SSID over Mesh can be used just like a cabled network of access points. AP & Repeater Modes The Vigor AP 1000C can be used as a st&-alone Wireless Access Point, to provide wireless connectivity for a router or network that doesn't currently have wireless. Access Point mode can create up to 4 separate Wireless networks (or SSIDs). The Vigor AP 1000C can provide completely separate private & guest wireless networks through the use of 802.1q VLAN tags with a router or network that supports VLAN tagging, such as the Dray Tek Vigor 2862 router. Range Extender (or Universal Repeater) mode allows the Vigor AP 1000C to extend the wireless coverage of any existing wireless network. In this mode, the Vigor AP 1000C connects to a remote wireless network, allowing it to provide Internet & Network access to wireless clients that connect to the Vigor AP 1000C's wireless network. Mesh
- Auto-Optimisation A Dray Tek Mesh Wireless network can easily add new Mesh Nodes & self-organises links between up to 8 Dray Tek Vigor AP access points, to ensure the best possible speeds. If a Mesh Node's wireless uplink drops out, for instance if there's interference or the Vigor AP it connects to is turned off, each Mesh Vigor AP automatically re-connects to the next available point to resumes service without any manual intervention required. Mesh Nodes further away will connect wirelessly to the nearest Mesh Node, with up to 3 wireless hops. Alternatively, where a network connection is available for a Vigor AP, join a Mesh Node to the network through ethernet & nearby wireless Mesh Nodes can join it instead of the Mesh Root to reduce wireless hops & increase possible Mesh throughput. Central Management with Dray Tek Vigor ACS The Dray Tek Vigor AP 1000C can be managed by the Dray Tek Vigor ACS central management system
- a cloud platform which can manage most Dray Tek products
- routers, wireless access points & Ethernet switches, giving you complete visibility & control of your Dray Tek product estate, even without a Dray Tek Vigor router on site. The Dray Tek Vigor ACS management system can be used to configure & provision Dray Tek Vigor AP access points, similarly to performing these actions through the Vigor AP's web interface, with a familiar menu layout in the Configuration section of Vigor ACS. Profiles for groups of access points can be provisioned in Vigor ACS by selecting a Vigor ACS network, then accessing Configuration > AP Profile to configure profiles & apply them selectively. Dray Tek's Vigor ACS management monitors each Vigor AP access point, with a Dashboard view giving a central overview of the most important information from the Vigor AP's current status. Central Management with a Dray Tek Router The Vigor AP 1000C can operate in standalone autonomous mode, but can also form part of a centrally managed wireless installation by adding a compatible Dray Tek wireless controller such as the Vigor 2862 router. This enables you to centrally control, manage & administer multiple AP devices installed around your building/campus. Management also enables efficient usage of your wireless access point through load-balancing, whereby wireless clients are distributed across several access points to reduce congestion. The Dray Tek router operating as the wireless controller can provision Dray Tek Vigor AP access points using the Central AP Management profiles configured on the router, with an option to Auto Provision
- auto configuring newly installed Vigor AP access points with the Auto Provisioning profile, upon initial connection to the Dray Tek Vigor router's network.




...

G.fast (Ultrafast Fibre) & VDSL2 (Superfast Fibre) to Ethernet Modem. Up to 330mbps download & 50mbps upload. Full-Bridge Modem & More
- Two operation modes for the Vigor 166 allow it to operate as a fully bridged Modem or mini Router. No Setup Needed
- Works as a modem wih most ISPs, straight out of the box. Pre-configured to work with most UK ISPs. Just set the username & password on your router. Add DSL connectivity to any Router
- Ideal Partner device for Dray Tek dual-WAN products or any other vendor's Ethernet WAN firewall. 2 Gigabit LAN Ports
- Connect two devices to the Vigor 166 with 2 Gigabit (10/1000 Mbps) ports. Compatible with IPTV & ISP Video on Demand services (You View, Sky Q). The Vigor 166 is a G.fast & VDSL2 35b modem to Ethernet bridge, connecting G.fast or VDSL to your Ethernet-based Router or Firewall. It provides proven compatibility with UK G.fast & VDSL2 technologies; extensively tested & tuned to provide a robust & reliable DSL connection.



...

The Vigor 2765 Vac is a VDSL or Ethernet WAN router with Gigabit performance, allowing you to make full use of Dray Tek's advanced feature set, with Quality of Service, VPN & Content Filtering. Connect the Vigor 2765 to Superfast Fibre with its integrated VDSL modem. Or connect to Virgin Media Cable & Ultrafast FTTP with Ethernet WAN. Either connection, or a 4G USB (Universal Serial Bus) modem can be used as the primary or Failover connections, so that if the main Internet connection goes down, the Vigor 2765 can use its backup connections to guarantee reliable Internet access & VPN connectivity. With integrated 802.11ac wireless, to provide fast & expansive wireless coverage to your network's computers & devices. Use the Vigor 2765 Vac's integrated Vo IP SIP ATA, to connect 2 analogue handsets to Voice over IP, to connect PSTN telephones & fax machines. Route Policy
- Routing Management for WAN & VPN The Vigor 2765 series provides full policy-based control of where & how outbound traffic is routed with Route Policy, to send traffic through VPN services & alternative LAN gateways. Powerful So Ho VPN Router Dray Tek's Vigor routers feature extensive VPN (Virtual Private Networking) capabilities. The Vigor 2765 series is no exception, its VPN capabilities are well suited to So Ho (small office, home office) environments. A VPN enables you to link remote offices & branch offices back to HQ, or home-based/mobile teleworkers back to your office. The Vigor 2765 means that you can make full use of Fibre broadband with VPN. Up to 200 Mbps of IPsec VPN throughput for fast & secure connections, to VPN services & other offices. Connect 2 VPN tunnels concurrently to access remote resources securely. Connect the Vigor 2765 in a branch office or home office to a head office for seamless access to network resources. It supports all common industry standard VPN protocols, for it to connect to VPN services, link remote offices & handle connections from all types of VPN clients. Supporting IPsec IKEv 1 & IKEv 2 protocols with EAP & XAuth authentication, Dray Tek's SSL VPN & L2TP for both LAN to LAN & Dial-In teleworker VPNs. In addition, teleworkers can connect to the router with Open VPN. User management for Dial-In Teleworkers is managed through the router's web interface, with m OTP 2-factor authentication available for IPsec, L2TP & SSL VPN Teleworker connections. Connecting Remote Sites with LAN to LAN VPN Supporting up to 2 concurrently active VPN tunnels & 200 Mbps of IPsec VPN throughput, the Vigor 2765 series is ideal as a branch-office or home-office router, to connect with a head office router such as the Vigor 3910. Once connected, they have access to your office/remote resources through a secure encrypted tunnel allowing remote desktop, file sharing & seamless access to other resources & devices. Dray Tek SSL VPN for Dial-In Teleworkers & LAN to LAN Connect up to 2 Dray Tek SSL VPN tunnels. These encrypted tunnels securely link teleworkers or remote Dray Tek Vigor routers back to your main office using SSL/TLS technology
- similar to the HTTPS security that's used for most secure websites on the internet such as on-line banking & shopping services. Teleworkers can connect with a secure SSL VPN tunnel to the Dray Tek Vigor 2765, using the free Dray Tek Smart VPN Client app. Available for Windows, mac OS, Apple i OS (iPad, iPhone) & Android devices. Connect VPNs from behind NAT with Dray Tek's VPN Matcher A typical requirement for connecting a VPN tunnel between two points is that the VPN server must be directly accessible on the public Internet. Sometimes this can be achieved with NAT Port Forwarding if the router is located behind another router, but if the router is connected to 4G Mobile Broadband or is behind Carrier-Grade NAT (CG-NAT), connecting to that VPN server may be impossible. Dray Tek's new VPN Matcher service helps Dray Tek routers behind NAT to allow Dial-In Teleworkers to connect, or connect two Dray Tek VPN routers that are behind NAT & could not normally establish a VPN tunnel. AC1300 Wireless LAN with Mesh The 2765 series 'ac' models provide 802.11ac simultaneous Dual-Band wireless for fast & efficient wireless connectivity. Multi-User MIMO allows the router to send to more than one device at a time, with each of its Antennas streaming data to different devices at once, improving efficiency over standard 802.11ac wireless & allowing the router to effectively serve more wireless clients. With firmware 4.3.0, the Vigor 2765 'ac' wireless routers can be used as part of Dray Tek's Mesh wireless system, allowing the router to work as the Mesh Root, providing Internet access & management of Mesh Vigor A Ps directly. 4 Gigabit LAN Ports with VLANs The Vigor 2765 series provides 4 Gigabit LAN ports for wired links to Computers, Servers & Network Attached Storage. 2 LAN subnets & VLANs allow the Vigor 2765 to provide a guest network fully separate from internal network data. Or any other configuration that can use 2 subnets, whether that's 2 wireless networks with different IP ranges, or a separate LAN subnet for printers & server. Each network can have its own Content Filtering, Firewall, Quality of Service & Route Policy configurations. The router has full support for 802.1Q VLAN tagging, so that these subnets can be passed to other devices that support VLAN tags, such as the Dray Tek Vigor Switch G1080 8-port switch, for additional network ports. The Wireless LAN also links to these VLANs, making the same Guest & Private networks possible simply using different wireless SSIDs. Or connect up a Dray Tek Vigor AP wireless access point, such as the Vigor AP 903 to do the same, spanning the router's own wireless & any connected wireless APs. Integrated Vo IP Telephone Ports The Vigor 2765 Vac features an integrated Vo IP ATA (Analogue Telephone Adapter). This connects two analogue phones to Voice over IP for use with hosted PBX systems & Vo IP/SIP telephone services. Either 1 or 2 telephones or DECT handsets can be connected, for use independently & simultaneously, for both incoming & outgoing calls. Use the ' Digit-Map' feature to direct calls through different SIP/ Vo IP services. For instance, local calls can be made through one Vo IP provider. International calls would route through an alternative Vo IP provider, with better pricing on calls outside of the UK. Digit Map allows for extremely flexible call routing. Integrating the Vo IP ATA into the router ensures that no port forwarding or NAT handling is typically needed. Simply connect the Vigor 2765 Vac to the Internet & configure your Vo IP account details to make & receive calls. Designed for Central Management The Vigor 2765 series can be centrally managed along with Vigor AP's & switches, with the Vigor ACS central management platform. This scalable solution provides visibility, control & reporting of your entire Dray Tek product estate, ideal for dealers/SIs managing customers' devices or any user who wants to know what's going on with their devices. Vigor ACS also provides features like automated/bulk firmware updates, VPN management & alarms for connectivity or other issues. Robust & Comprehensive IPv 4 / IPv 6 Firewall Security is always taken seriously with Dray Tek routers. The firewall protects against attacks including Do S (Denial of Service) attacks, IP-based attacks & access by unauthorised remote systems. Wireless, Ethernet & VPN are also protected by various protection systems. The Dray Tek object-based firewall enables you to create combinations of Firewall rules & Content Filtering to suit a home or small office environment, applying Content Filtering to the whole network, only specified devices or just the network that guests can connect to. The Vigor 2765 supports both IPv 4 & IPv 6 with Dual-Stack IPv 4/IPv 6. Advanced networking features, such as the object-based Firewall, Quality of Service, Content Filtering & VLANs support both IPv 4 & IPv 6 networks. Web Content Filtering with DNS Filter The content control features of the Vigor 2765 allow you to set restrictions on web site access, blocking download of certain file or data types, blocking specific web sites with whitelists or blacklists, blocking IM/P2P applications or other potentially harmful or wasteful content. Restrictions can be per user, per PC or universal & according to time schedules. Content filtering can also block sites using HTTPS/SSL where URLs are encrypted (and normal routers cannot block). Using the Global View service, you can block whole categories of web sites (e.g. gambling, adult sites etc.), subject to an annual subscription, which is continuously updated with new or changed site categorisations or sites which have become compromised (such as infected with Malware). A free 30-day trial is included with your new router. Quality of Service with App Qo S Prioritise latency-sensitive applications on your network with Quality of Service. App Qo S simplifies setting up Quality of Service significantly, simply select which applications or services to prioritise, such as Zoom & Skype. Use 4 separate queues to give priority to servers & PCs (IP address), services such as Vo IP or DNS, or packet tagging used by IP phones with 802.1p & DSCP support Auto Voice VLAN allows the router to automatically prioritise Vo IP calls as they pass through the router without additional configuration. Control throughput with Bandwidth Limit, by setting speed limits for all clients individually, groups of IPs, or a shared bandwidth limit for a whole subnet, such as a Guest network. Central AP & Switch Management The Vigor 2765 can manage & aid in setting up Vigor AP access points & Vigor Switch switches, connected locally to the router. This enables you to centrally control, manage & administer multiple AP & Switch devices installed around your home or office, through the router's web interface for local or remote setup. Central AP Management The Dray Tek router can manage 2 Dray Tek Vigor AP access points with Central AP Management profiles, with an option to Auto Provision
- auto configuring newly installed Vigor AP access points with the Auto Provisioning profile, upon initial connection to the Dray Tek Vigor router's network. Central Switch Management Dray Tek Vigor Switch switches can be provisioned & managed through the router with Dray Tek’s Central Switch Management system, which allows you to: Easily provision VLAN configuration & other port settings directly from the router. Set bandwidth rate limits & schedules for individual ports. Log switch events for alert notifications if network problems occur At a glance see the devices connected on your network with a virtual topology.


...