Hyper X FURY Low Voltage 4GB DDR3L 1866 M Hz Memory Hyper X HX316LC10FB/4 is a 512M x 64-bit (4GB) DDR3L-1600 CL10 SDRAM (Synchronous DRAM) 1 Rx 8, low voltage, memory module, based on eight 512M x 8-bit DDR3 FBGA components. Each module kit supports Intel Extreme Memory Profiles (Intel XMP) 2.0. This module has been tested to run at DDR3L-1600 at a low latency timing of 10-10-10 at 1.35V. Additional timing parameters are shown in the Pn P Timing Parameters section below. The JEDEC standard electrical & mechanical specifications areas follows: Pn P JEDEC TIMING PARAMETERS: JEDEC/ Pn P: DDR3L-1600 CL10-10-10 @1.35V/1.5V DDR3L-1333 CL9-9-9 @1.35V/1.5V DDR3L-1066 CL7-7-7 @1.35V/1.5V XMP Profile 1: DDR3L-1600 CL10-10-10 @1.35V FEATURES JEDEC standard 1.35V & 1.5V Power Supply VDDQ = 1.35V & 1.5V 800 M Hz f CK for 1600 Mb/sec/pin independent internal bank Programmable CAS Latency: 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE ≤ 95°C Asynchronous Reset Height 1.291” (32.80mm) w/heatsink, single sided component 726074 SPECIFICATIONS CL (IDD) 10 cycles Row Cycle Time (t R Cmin) 44.75ns (min.) Refresh to Active/ Refresh Command Time (t RFCmin) 260ns (min.) Row Active Time (t RASmin) 32.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to +85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used.


...

Hyper X FURY Low Voltage 8GB DDR3L 1600 M Hz Memory Hyper X HX316LC10FB/4 is a 512M x 64-bit (4GB) DDR3L-1600 CL10 SDRAM (Synchronous DRAM) 1 Rx 8, low voltage, memory module, based on eight 512M x 8-bit DDR3 FBGA components. Each module kit supports Intel Extreme Memory Profiles (Intel XMP) 2.0. This module has been tested to run at DDR3L-1600 at a low latency timing of 10-10-10 at 1.35V. Additional timing parameters are shown in the Pn P Timing Parameters section below. The JEDEC standard electrical & mechanical specifications areas follows: Pn P JEDEC TIMING PARAMETERS: JEDEC/ Pn P: DDR3L-1600 CL10-10-10 @1.35V/1.5V DDR3L-1333 CL9-9-9 @1.35V/1.5V DDR3L-1066 CL7-7-7 @1.35V/1.5V XMP Profile 1: DDR3L-1600 CL10-10-10 @1.35V FEATURES JEDEC standard 1.35V & 1.5V Power Supply VDDQ = 1.35V & 1.5V 800 M Hz f CK for 1600 Mb/sec/pin independent internal bank Programmable CAS Latency: 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE ≤ 95°C Asynchronous Reset Height 1.291” (32.80mm) w/heatsink, single sided component SPECIFICATIONS CL (IDD) 10 cycles Row Cycle Time (t R Cmin) 28.125ns (min.) Refresh to Active/ Refresh Command Time (t RFCmin) 260ns (min.) Row Active Time (t RASmin) 37.5ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to +85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used.


...

Hyper X FURY Low Voltage 8GB DDR3L 1866 M Hz Memory Hyper X HX316LC10FB/4 is a 512M x 64-bit (4GB) DDR3L-1600 CL10 SDRAM (Synchronous DRAM) 1 Rx 8, low voltage, memory module, based on eight 512M x 8-bit DDR3 FBGA components. Each module kit supports Intel Extreme Memory Profiles (Intel XMP) 2.0. This module has been tested to run at DDR3L-1600 at a low latency timing of 10-10-10 at 1.35V. Additional timing parameters are shown in the Pn P Timing Parameters section below. The JEDEC standard electrical & mechanical specifications areas follows: Pn P JEDEC TIMING PARAMETERS: JEDEC/ Pn P: DDR3L-1600 CL10-10-10 @1.35V/1.5V DDR3L-1333 CL9-9-9 @1.35V/1.5V DDR3L-1066 CL7-7-7 @1.35V/1.5V XMP Profile 1: DDR3L-1600 CL10-10-10 @1.35V FEATURES JEDEC standard 1.35V & 1.5V Power Supply VDDQ = 1.35V & 1.5V 800 M Hz f CK for 1600 Mb/sec/pin independent internal bank Programmable CAS Latency: 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE ≤ 95°C Asynchronous Reset Height 1.291” (32.80mm) w/heatsink, single sided component 726074 SPECIFICATIONS CL (IDD) 10 cycles Row Cycle Time (t R Cmin) 44.75ns (min.) Refresh to Active/ Refresh Command Time (t RFCmin) 260ns (min.) Row Active Time (t RASmin) 32.125ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to +85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used.


...

Hyper X FURY Low Voltage 8GB Kit DDR3L 1600 M Hz Memory (2x 4GB) Hyper X HX316LC10FB/4 is a 512M x 64-bit (4GB) DDR3L-1600 CL10 SDRAM (Synchronous DRAM) 1 Rx 8, low voltage, memory module, based on eight 512M x 8-bit DDR3 FBGA components. Each module kit supports Intel Extreme Memory Profiles (Intel XMP) 2.0. This module has been tested to run at DDR3L-1600 at a low latency timing of 10-10-10 at 1.35V. Additional timing parameters are shown in the Pn P Timing Parameters section below. The JEDEC standard electrical & mechanical specifications areas follows: Pn P JEDEC TIMING PARAMETERS: JEDEC/ Pn P: DDR3L-1600 CL10-10-10 @1.35V/1.5V DDR3L-1333 CL9-9-9 @1.35V/1.5V DDR3L-1066 CL7-7-7 @1.35V/1.5V XMP Profile 1: DDR3L-1600 CL10-10-10 @1.35V FEATURES JEDEC standard 1.35V & 1.5V Power Supply VDDQ = 1.35V & 1.5V 800 M Hz f CK for 1600 Mb/sec/pin independent internal bank Programmable CAS Latency: 11, 10, 9, 8, 7, 6 Programmable Additive Latency: 0, CL
- 2, or CL
- 1 clock 8-bit pre-fetch Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with t CCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe Internal (self) calibration: Internal self calibration through ZQ pin (RZQ: 240 ohm ± 1%) On Die Termination using ODT pin Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE ≤ 95°C Asynchronous Reset Height 1.291” (32.80mm) w/heatsink, single sided component SPECIFICATIONS CL (IDD) 10 cycles Row Cycle Time (t R Cmin) 48.125ns (min.) Refresh to Active/ Refresh Command Time (t RFCmin) 260ns (min.) Row Active Time (t RASmin) 37.5ns (min.) Maximum Operating Power TBD W* UL Rating 94 V
- 0 Operating Temperature 0oC to +85oC Storage Temperature -55oC to +100oC * Power will vary depending on the SDRAM used.


...

FURY Pro Gaming Mouse Pad has a high-quality fabric pad that’s soft yet resistant & heat-treated for a controlled glide to put you in the lead, whether you’re a gamer in a death match or a professional racing the clock. FURY’s natural rubber & cross-weave underside provide padding for your wrist to keep you comfortable & supported & help the pad grip the surface firmly for more stability. Available in four sizes from 290–900MM wide & 240–420mm high, with 3–4mm pad thickness, Hyper X FURY fits any style & space requirement & is a great value that gives you greater surface without a higher cost. The compact sizes are ideal for mobile computing & LAN parties, while the largest size covers a full-sized desk for a smooth work or play surface. It’s easy to roll up or fold & wear-resistant so the pad keeps its shape through epic battles, late-night work sessions & more. ...

Get in the game with Hyper X FURY. Even newbies get up to speed fast, since FURY automatically recognises its host platform & automatically overclocks to up to 1866 M Hz, providing plenty of power for your next death match. FURY's asymmetric heatspreader design lets you stand out from the crowd. It's available in black, blue, red & -- for the first time in the Hyper X line -- white, with a black PCB. So your rig can reflect your style & you can show it off with pride. It's 100-percent tested & LAN-ready plus it's backed by free technical support. Hyper X Pn P memory will run in most DDR3 systems up to the speed allowed by the manufacturer's system BIOS. Pn P cannot increase the system memory speed faster than is allowed by the manufacturer's BIOS. Hyper X FURY is available in frequency speeds from 1333 M Hz to 1866 M Hz. Reach faster speeds & higher capacities by just installing the memory, no adjustments in BIOS needed. No matter if you are an Intel or AMD gamer, the Hyper X FURY is ideal for you. To make sure it works, Hyper X FURY has been tested with popular brands of motherboards. Does your system have enough memory to get you into the game? Kits are available to max out your system's memory with up to 16GB of high-performance goodness. ...

Hyper X FURY DDR4 RGB1 delivers a boost of performance & style with speeds of up to 3733 M Hz 2, aggressive styling, & RGB lighting that runs the length of the module for smooth & stunning effects. This dazzling, cost-effective upgrade is available in 2400 M Hz–3733 M Hz speeds, CL15–19 latencies, single module capacities of 4GB–32GB, & kit capacities of 16GB–128GB. It features Plug N Play automatic overclocking at 2400 M Hz & 2666 M Hz speeds & is both Intel XMP-ready & Ready for Ryzen. Hyper X FURY DDR4 RGB stays cool with its stylish, low-profile heat spreader. 100% tested at speed & backed by a lifetime warranty, it’s an easy, worry-free upgrade for your Intel or AMD-based system. Customizable RGB lighting with aggressive styling 1 Give your battle station a stylish upgrade thanks to FURY DDR4 RGB’s updated heat spreader & customizable smooth, stunning RGB effects. Use the powerful Hyper X NGENUITY software or motherboard manufacturer’s software to create your own look. Hyper X Infrared Sync Technology RGB effects stay synced thanks to Hyper X’s patented infrared sync technology. Intel XMP-Ready Our engineers have predefined Intel Extreme Memory Profiles designed to maximize the performance of our memory modules, reaching speeds up to 3733 M Hz. Ready for AMD Ryzen Get memory that’s Ready for Ryzen & will seamlessly integrate with your AMD-based system. A reliable, compatible performance boost for your build. Plug N Play – Automatic overclocking up to 2666 M Hz 2 A simple & easy Plug N Play upgrade, Hyper X FURY DDR4 RGB will auto-overclock itself to the highest listed speed allowed by the system BIOS. Some legacy chipsets/processors from Intel prior to 8th Gen have not been updated to support memory modules featuring DDR4 16 Gbit density DRAM. Check with system or motherboard manufacturer for an updated BIOS to support 16 Gbit DRAM. 1. Lighting customizable with Hyper X NGENUITY software or with motherboard RGB control software. RGB customization support through third-party software may vary. 2. Hyper X Plug N Play memory will run in DDR4 systems up to the speed allowed by the manufacturer’s system BIOS. Pn P cannot increase the system memory speed faster than is allowed by the manufacturer’s BIOS. Hyper X Plug N Play DDR4 products support XMP 2.0 specifications so overclocking can also be achieved by enabling the built-in XMP Profile. Main Features stunning RGB lighting with aggressive style[1] Patented Hyper X Infrared Sync Technology Intel XMP-ready Ready for AMD Ryzen Speeds up to 3733 M Hz & kit capacities up to 128GB Plug N Play functionality at 2400 M Hz & 2666 M Hz[2] ...

Hyper X FURY DDR4 RGB1 delivers a boost of performance & style with speeds of up to 3733 M Hz 2, aggressive styling, & RGB lighting that runs the length of the module for smooth & stunning effects. This dazzling, cost-effective upgrade is available in 2400 M Hz–3733 M Hz speeds, CL15–19 latencies, single module capacities of 4GB–32GB, & kit capacities of 16GB–128GB. It features Plug N Play automatic overclocking at 2400 M Hz & 2666 M Hz speeds & is both Intel XMP-ready & Ready for Ryzen. Hyper X FURY DDR4 RGB stays cool with its stylish, low-profile heat spreader. 100% tested at speed & backed by a lifetime warranty, it’s an easy, worry-free upgrade for your Intel or AMD-based system. Customizable RGB lighting with aggressive styling 1 Give your battle station a stylish upgrade thanks to FURY DDR4 RGB’s updated heat spreader & customizable smooth, stunning RGB effects. Use the powerful Hyper X NGENUITY software or motherboard manufacturer’s software to create your own look. Hyper X Infrared Sync Technology RGB effects stay synced thanks to Hyper X’s patented infrared sync technology. Intel XMP-Ready Our engineers have predefined Intel Extreme Memory Profiles designed to maximize the performance of our memory modules, reaching speeds up to 3733 M Hz. Ready for AMD Ryzen Get memory that’s Ready for Ryzen & will seamlessly integrate with your AMD-based system. A reliable, compatible performance boost for your build. Plug N Play – Automatic overclocking up to 2666 M Hz 2 A simple & easy Plug N Play upgrade, Hyper X FURY DDR4 RGB will auto-overclock itself to the highest listed speed allowed by the system BIOS. ...

Hyper X FURY DDR4 RGB introduces stunning RGB lighting with an aggressive style, stay cool whilst unleashing your FURY. Its ...

Hyper X FURY DDR4 RGB1 delivers a boost of performance & style with speeds of up to 3733 M Hz 2, aggressive styling, & RGB lighting that runs the length of the module for smooth & stunning effects. This dazzling, cost-effective upgrade is available in 2400 M Hz–3733 M Hz speeds, CL15–19 latencies, single module capacities of 4GB–32GB, & kit capacities of 16GB–128GB. It features Plug N Play automatic overclocking at 2400 M Hz & 2666 M Hz speeds & is both Intel XMP-ready & Ready for Ryzen. Hyper X FURY DDR4 RGB stays cool with its stylish, low-profile heat spreader. 100% tested at speed & backed by a lifetime warranty, it’s an easy, worry-free upgrade for your Intel or AMD-based system. Customizable RGB lighting with aggressive styling 1 Give your battle station a stylish upgrade thanks to FURY DDR4 RGB’s updated heat spreader & customizable smooth, stunning RGB effects. Use the powerful Hyper X NGENUITY software or motherboard manufacturer’s software to create your own look. Hyper X Infrared Sync Technology RGB effects stay synced thanks to Hyper X’s patent-pending infrared sync technology. Intel XMP-Ready Our engineers have predefined Intel Extreme Memory Profiles designed to maximize the performance of our memory modules, reaching speeds up to 3733 M Hz. Ready for AMD Ryzen Get memory that’s Ready for Ryzen & will seamlessly integrate with your AMD-based system. A reliable, compatible performance boost for your build. Plug N Play – Automatic overclocking up to 2666 M Hz 2 A simple & easy Plug N Play upgrade, Hyper X FURY DDR4 RGB will auto-overclock itself to the highest listed speed allowed by the system BIOS. 1. Lighting customizable with Hyper X NGENUITY software or with motherboard RGB control software. RGB customization support through third-party software may vary. 2. Hyper X Plug N Play memory will run in DDR4 systems up to the speed allowed by the manufacturer’s system BIOS. Pn P cannot increase the system memory speed faster than is allowed by the manufacturer’s BIOS. Hyper X Plug N Play DDR4 products support XMP 2.0 specifications so overclocking can also be achieved by enabling the built-in XMP Profile. Main Features stunning RGB lighting with aggressive style 1 Patented Hyper X Infrared Sync Technology Intel XMP-ready Ready for AMD Ryzen Speeds up to 3733 M Hz & kit capacities up to 128GB Plug N Play functionality at 2400 M Hz & 2666 M Hz 2 ...