A single Flex Stack connection between two members is a full duplex 10 Gbps connecton. Each Cisco Catalyst 2960-S member supports two Flex Stack connections. Each Flex Stack member can simultaneously send & receive Ethernet traffic over both stack links at line rate, effectively giving 20 Gbps of stack bandwidth per member. Up to four switches can stacked together using Flex Stack to form a single logical switch. Logical switch is another term used to identify a stack of switches. There are multiple physical switches acting as a single unit. This single unit behavior is a logical switch. Cisco Catalyst 2960-S switches running Flex Stack use a hop-by-hop method of transferring Ethernet packets across the stack. Packets traverse the stack by going from one member to another over the Flex Stack links until the packet reaches its destination. This is the same behavior as multiple standalone Ethernet switches forwarding packets from one switch to another. ...

A single Flex Stack connection between two members is a full duplex 10 Gbps connecton. Each Cisco Catalyst 2960-S member supports two Flex Stack connections. Each Flex Stack member can simultaneously send & receive Ethernet traffic over both stack links at line rate, effectively giving 20 Gbps of stack bandwidth per member. Up to four switches can stacked together using Flex Stack to form a single logical switch. Logical switch is another term used to identify a stack of switches. ...

Replacement of the standard Cisco 7960 footstand is required. The standard footstand is replaced with a two-piece footstand specifically designed to support the Cisco 7914. A double footstand enables two Cisco 7914 Expansion Modules to be used on a single Cisco 7960. ...

Product Description When adding the CP-7914 expansion module, a replacement footstand & an additional power supply are required. If one CP-7914 is being added, a CP-SINGLFOOTSTAND & a single power supply (3RD-PWR-CUBE or CP-PWR-CUBE) is needed. If two CP-7914's are being added, a CP-DOUBLFOOTSTAND & two power supplies are needed. The only tool required for installation of the Cisco 7914 is a flat blade screwdriver or other appropriate tool to unlatch the pins securing the standard footst&. About the Cisco CP-7914 Expansion Module: The Cisco IP Phone Expansion Module 7914 extends the capabilities of the Cisco IP Phones 7960G, 7961G, 7970G & 7971G-GE with additional buttons & an LCD display. With this expansion module, you add 14 buttons to the existing six buttons of the Cisco IP Phones 7960 & 7961G & the existing eight buttons of the Cisco IP Phones 7970G & 7971G-GE, increasing the total number of buttons when you add one or two Cisco 7914 Expansion Modules. You can use up to two Cisco 7914 Expansion Modules with a Cisco IP Phones 7960G, 7961G, 7970G or 7971G-GE. The large LCD display of the Cisco IP Phone Expansion Module allows for quick & easy identification of associated buttons. Using the Settings menu of the host IP phone you can adjust the contrast of the individual LCDs for the phone & the expansion module according to your preference. The 14 buttons on each Cisco IP Phone Expansion Module 7914 can be programmed as a directory number (DN), line key, or speed-dial key, much like the Cisco IP Phones 7960G, 7961G, 7970G & 7971G-GE. When used as a DN key, buttons are illuminated, allowing easy identification of call state. ...

Rack mounting kit Designed For: Nexus 9504, 9504 Chassis Bundle, 9508, 9508 Chassis Bundle, 9516 ...

- Product Description: Cisco Fourth-Generation Multi-flex Trunk Voice/ Channelized Data T1/ E1 Module
- expansion module
- Device

...

The Cisco 1000BASE-LX/LH GBIC (WS-G5486) fully complies with the IEEE 802.3z 1000BASE-LX standard. However, its higher optical quality allows it to reach 6.2 miles (10 kilometers) over single-mode fiber (SMF), compared with the 3.1 miles (5 km) specified in the standard. Please note: networking components such as switches, routers, UPS & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

The Cisco Gigabit Ethernet Enhanced High-Speed WAN interface cards (EHWICs) can reduce your company's total cost of ownership (TCO) by integrating Gigabit Ethernet (GE) switch ports. These low-density Gigabit Ethernet switches offer small to medium-sized business (SMB) & enterprise branch-office customers a combination of switching & routing integrated into a single device. The Gigabit Ethernet EHWICs provide line-rate Layer 2 switching across onboard Gigabit Ethernet ports. Please note: networking components such as switches, routers, UPS & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

CISCO 100BASE-X SFP FOR FAST ETHERNET SFP PORTS PRODUCT OVERVIEW The Cisco 100BASE-X Small Form-factor Pluggable (SFP) is a hot-swappable input/output device that plugs into a Fast Ethernet port or slot, linking the port with the network. Main features include the following: Hot-swappable when deployed, the switch or router does not have to reboot. Supports the "pay-as-you-populate" model. Interchangeable with other 100BASE-X SFPs on the same line card. Supports the Cisco quality ID feature that enables the switch or router to identify whether or not the SFP is a Cisco qualified SFP. Optically interoperable with respective 100BASE-X Ethernet interfaces on the same link ...

The Cisco 100BASE-FX Small Form-Factor Pluggable (SFP) Fast Ethernet Interface Converter (GLC-GE-100FX=) is a hot-swappable device that plugs into a Gigabit Ethernet SFP port on Cisco Catalyst 3750 Series, 3560 Series, & 2970 Series switches. The Cisco SFP provides full-duplex 100-Mbps connectivity between switches over multimode fiber (MMF) infrastructures. It offers investment protection & an easy migration path for customers moving to Gigabit Ethernet connections in the future. The 100BASE-FX SFP operates on ordinary multimode fiber optical link spans of up to 2 kilometers in length. Customers implementing Cisco 100BASE-FX SFP can use 1000BASE-X SFPs in the future (including SX, LX/LH, ZX, & coarse wavelength-division multiplexing SFPs). Main features include the following Hot-swappable when deployed, the switch or router does not have to reboot Supports the “pay-as-you-populate” model Interchangeable with other 100BASE-X SFPs on the same line card Supports the Cisco quality ID feature that enables the switch or router to identify whether or not the SFP is a Cisco qualified SFP Optically interoperable with respective 100BASE-X Ethernet interfaces on the same link Please note: networking components such as switches, routers, UPS & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. ...