Cisco SFP+ Copper Twinax Cable
- Twinaxial cable
- SFP+
- SFP+
- 1 m
- for Catalyst 2960, 2960-24, 2960-48, 2960G-24,




...

The range of Cisco 10GBASE XENPAK modules offers customers a wide variety of 10 Gigabit Ethernet connectivity options for data center, enterprise wiring closet, & service provider transport applications. Cisco 10GBASE XENPAK modules provide flexibility of interface choice & support 10GBASE Ethernet. These hot-swappable input/output devices plug into an Ethernet XENPAK port of a Cisco switch or router to link the port with the network & support the Cisco quality identification (ID) feature that enables a Cisco switch or router to identify whether the module is a Cisco certified & tested XENPAK module. Cisco 10GBASE XENPAK modules also support pay-as-you-populate model. ...

Cisco 10GBASE-SR XFP module for MMF The 10GBASE-SR XFP is dedicated to Ethernet applications only. It supports a link length of 26m on standard FDDI-grade MMF. Up to 300m link lengths are possible when using 2000 MHz/km MMF (OM3). Up to 400m link lengths are possible when using 4700 M Hz*km MMF (OM4). Features Supports 10GBASE Ethernet & OC-192/STM-64 data rates Hot-swappable input/output device plugs into a XFP port of a Cisco Systems router to link the port with the network Provides flexibility of interface choice Supports “pay-as-you-populate” model Supports the digital optical monitoring capability Supports the Cisco quality identification (ID) feature that helps enable a Cisco switch or router to identify whether the module is a Cisco certified & tested XFP Supports optical interoperability with respective Cisco 10GBASE XENPAK & X2, & SFP+ modules on the same link ...

The power injector increases wireless LAN deployment flexibility of the access point by combining 55-VDC power with the data signal, & sending both to the connected access point. The power injector combines 55-VDC power (supplied by internal power supply) with the data signal, sending both to the access point. The power injector provides up to 60 W over all four wire pairs of shielded, outdoor rated Ethernet cable. The total length of the Ethernet cable from the AP to the switch must not exceed 320 ft (100 m). The wire gauge of the cable must be 26 AWG. The Ethernet cable from the switch to the power injector must be a shielded CAT5e or higher Ethernet cable. The Ethernet cable from the power injector to the access point must be a shielded outdoor-rated CAT5e or higher Ethernet cable with a 0.20 to 0.35 inch diameter. A shielded, outdoor Ethernet cable connects the power injector to a 10/100/1000 Ethernet switch, hub, or network, & another shielded, outdoor cable carries power & data to the access points Ethernet port. The power injectors AC power receptacle connects an approved AC power cord to a wall outlet or power strip. The power injector can be mounted on most horizontal & vertical surfaces, but must be mounted in a vertical orientation to comply with safety requirements. ...

The PVDM3 provides higher density & more processing power than the PVDM2, making the addition of rich-media applications possible. Enhanced DSP architecture accommodates a packet-processing engine optimized for rich-media voice & video applications, while concurrently supporting the time-division multiplexing IP (TDM-IP) voice framework used by the PVDM2. The PVDM3 module portfolio has up to 4 times higher density than those in the PVDM2 portfolio. In addition, the PVDM3 modules provide better density for medium- & high-complexity codecs than their equivalent PVDM2 peers. For example, the number of supported medium-complexity codec on a PVDM3-64 is 42, versus 32 on a PVDM2-64. Features High density & flexibility The PVDM3 module portfolio has up to 4 times higher density than those in the PVDM2 portfolio. In addition, the PVDM3 modules provide better density for medium- & high-complexity codecs than their equivalent PVDM2 peers. For example, the number of supported medium-complexity codec on a PVDM3-64 is 42, versus 32 on a PVDM2-64. Voice-quality management The PVDM3 modules perform compression, voice-activity-detection, jitter-management, and echo-cancellation functions. The echo cancellation offered in the PVDM3 modules has a tail length of 128 milliseconds (ms) & complies with ITU-T G.168. Energy-saving feature The PVDM3 DSPs offer multiple power-saving modes, including a power-saver mode when the module is not in use. In power-saver mode each PVDM3 can save up to 5 watts of power. ...

1520/1550 Series Power Injector The power injector (AIR-PWRINJ1500-2=) has three LEDs on the front end of the case Monitoring the Power Injector LEDs You can use the AP Power, Fault, & AC Power LEDs to check the power injector status. The LEDs provide the following status information: AP Power LED— Turns solid green after successful discovery; indicates that power injector is supplying power to the access point. Fault LED— Turns solid red when a fault occurs during discovery mode or power-up. Check Ethernet cables & connections before contacting your support organization for assistance. AC Power LED— Turns solid green when power injector is receiving AC power & is ready to provide power to the access point. Image; 1
- Mounting tab 2
- Access point power LED 3
- Fault LED 4
- AC power LED 5
- Ethernet connector (RJ-45) to access point (10/100/1000BASE-T) 6
- Ethernet connector (RJ-45) to switch (10/100/1000BASE-T) Do not use any other power injector or switch for Power over Ethernet with the 1550 Series access points. The 1550 Series is approved for use only with the AIR-PWRINJ1500-2=. You must also specify the country type power cord for the power injector. The AIR-PWRINJ1500-2= is for indoor use only. It has built-in surge protection, but you may also need to install a surge protector at the building entry point. Please check your local electrical regulations.





...

Pole mount kit needed to install the access point on a vertical or horizontal metal, wood, or fiberglass pole, along with Customer banding strap tool (BAND IT)
- AIR-B&-INST-TL= Pole mount kit (AIR-ACCPMK1550=) Pole clamp bracket Two gusset strap brackets One mounting bracket Twelve hex bolts (M8 x 16) One M8 flange nut Six M8 flat washers Ten M8 split lock washers Two stainless steel mounting straps
...

The High-Density Packet Voice digital signal processor (DSP) Module (PVDM2) enables Cisco Systems Integrated Services Routers to provide high-density voice connectivity, conferencing, & transcoding capabilities in Cisco IP Communications solutions. Cisco Integrated Services Routers provide enterprises & service providers with a toll bypass solution by connecting their existing telephony equipment (such as private branch exchanges [PBXs], Key systems, analog telephones, & fax machines) to a toll-free data network; & eventually migrate customers to Cisco AVVID (Architecture for Voice, Video & Integrated Data) IP telephony solutions. ...

Cisco 1645683X4 K WRLS N Access Point W PWR Over Enet Please note: networking components such as switches, routers, UPS & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

Designed For UCS B200 M4 Entry Smart Play, B200 M4 Performance Smart Play, B200 M4 value Smart Play, C220 M4 Entry Plus ...