Part of the comprehensive Allied Telesis 2911 Series, the AT-2911SX Network Interface Card continues the Allied Telesis tradition of providing reliable fiber adapter cards. Gigabit cards boost the speed of the network up to ten times over a standard Fast Ethernet card to 1000MB per second. The PCIe x 1 bus provides the latest technology, enabling the maximum throughput in the smallest form factor possible. ...

The Allied Telesis' range of Fast Ethernet Media converters provides a complete series of conversion devices, allowing users to extend the size of UTP & multi-mode fiber networks with the use of single-mode fiber cabling. Supporting SC-connected single-mode fiber, these converters can be used to extend networks up to a distance of 2km. All these media converters feature an internal MDI/MDIX switch, allowing the converter to be connected to PC, hub or switch with a simple UTP cable. The media converters also allow the installer to test the integrity of fiber connection, by forcing the converters to communicate over the fiber cable. This Link Test feature allows installers to check for cable faults without the need for expensive fiber optic test equipment. Please note: networking components such as switches, routers, UPS & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

The Allied Telesis range of 850nm fiber Fast Ethernet media converters allows users to extend the size of UTP networks with the use of fiber cabling. Converting between 10T & 10FL or 100TX & 100SX fiber quickly & reliably, the AT-MC116XL addresses the growing demand for a low-cost solution for fiber installations of 300 meters or less. To maximize flexibility, the converter is available in SC fiber connector style. The AT-MC116XL auto-negotiates during the link up phase of the connection to set the speed (10/100) & operation mode (Full or Half Duplex). When connecting media converters to autonegotiating Fast Ethernet switches, this media converter will automatically connect the link in either Full or Halfduplex mode, allowing the link to be established with the greatest bandwidth. The Missing Link feature allows accurate reporting to network management systems as well as allowing devices with redundant link capability to be inter-connected with these media converters, failure in one fiber link will be signaled to the switch, allowing the second link to become active. Please note: networking components such as switches, routers, UPS & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

The AT-TRAY1 is a "shelf " style unit designed to hold one Allied Telesis standalone media converter. The AT-TRAY1 can be installed on any type of standard rack rail or it can be wall-mounted. It is designed to be installed vertically to the inside or outside of the rack rail. ...

The AT-CV5001 shares common line cards with other Converteon chassis for easier inventory management & smoother product deployment. Please note: networking components such as switches, routers, UPS & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

The AT-GS900 series of unmanaged Gigabit Layer 2+ switches offer seamless & simple connectivity to your existing network infrastructure. Wall, desk, & rack-mounting options give you the flexibility to chose a model that meets your deployment needs. Please note: networking components such as switches, routers & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

Founded with the goal of producing reliable, standards-based networking products, Allied Telesis bridges the gap left by other Ethernet networking manufacturers, whose solutions are limited in scope or cost-prohibitive. The AT-MCF2000AC module is an AC power supply unit for the AT-MCF2000 series of media converter chassis The power supply module has two LEDs
- PSU
- FAN

Specification Input Voltage 100-240 VAC 50/60 Hz Output Voltage 12 volts & 3.3 volts Operating Temperature: 0° C to 40° C
- (32° F to 104° F) Storage Temperature: -20° C to 70° C
- (-° 4F to 158° F) Operating Humidity: Less than 80% noncondensing Storage Humidity: Less than 95% noncondensing Maximum Operating Altitude: 3, 048 m (10, 000 ft) Maximum Nonoperating Altitude: 4, 000 m (13, 000 ft)





...

The Allied Telesis AT-FS716 series provides powerful 10/100 switching solutions to desktop & small network environments. Each switch features full autonegotiating 10/100 ports, which automatically detect speed & duplex modes of attached devices & allow the switch to automatically configure for the best possible performance. Choose from 5, 8, 16, or 24 port models. With both internal or external power supplies, the AT-FS700 series can meet a multitude of power requirements. Wall, desk, & rack mounting options give users ultimate flexibility in choosing a model to meet their physical deployment requirements. The AT-FS700 series switches are fully auto-configuring requiring minimal or no set-up by the user. The autosensing ports allow seamless & simple connectivity between existing 10 Mbps Ethernet & 100 Mbps Fast Ethernet UTP devices, & all units can be installed in minutes. All models are equipped with a MDI/MDIX port (s) for simple connection to other hubs & switches. Front panel LEDs allow users to monitor the switch status providing simple "at a glance" management. Please note: networking components such as switches, routers & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

The Allied Telesis' range of Fast Ethernet media converters allows users to extend the size of UTP networks with the use of fiber cabling. Converting between 100 Base-TX or 100 Base-FX Multi-mode & 100 Base-FX Single-mode " Long Haul" quickly & reliably, the AT-MC103LH & AT-MC104LH can be used to extend networks with up to 40km of fiber. The AT-MC103LH (with UTP connection) features an internal MDI/MDIX switch, allowing the converter to be connected to a PC, hub or switch with a simple UTP cable. Both media converters also allow the installer to test the integrity of fiber connection, by forcing the converters to communicate over the fiber cable. This Link Test feature allows installers to check for cable faults without the need for expensive fiber optic test equipment. Please note: networking components such as switches, routers, UPS & wireless devices require that speeds & standards be consistent throughout the network to gain optimum performance. To avoid compatibility clashes or for advice, please contact us on solutions@ebuyer.com. ...

Allied Telesis' simply connects the IP world with affordable, highly reliable, end-to-end networking solutions. The company's broad line of networking products builds systems that meet today's demand for efficient, effective connectivity
- in small networks, across the enterprise, & over remote links. Allied Telesis' makes the most challenging network designs a reality, with a variety of products for network systems that optimize for any distance, speed, security or legacy integration priority. For maximum protection against service interruption, Allied Telesis' offers a hot-swappable auxiliary power supply unit, the AT-PWR4. The AT-PWR4 provides automatic load balancing for one or two power supplies & on-the-fly switching in case of power supply failure.
...