This is a white granular powder which when added to water produces a solution which is ideal for unblocking drains & heavy-duty cleaning. Unblocking drains or pipes sprinkle the contents of the pack into 5 litres of cold water & stir with a stick. take care, as product will heat up. pour immediately & carefully down the drain or pipe. after 20-30 minutes flush with boiling water. repeat if necessary.
heavy-duty cleaning use same method as above however use approx. 125g of caustic per 5 litres of water. rinse areas thoroughly after use with clean fresh water.
...

Everflex silicone 335 construction is a low modulus, reactive curing silicone sealant that cures quickly to reduce dirt pick up. it remains permanently flexible, forming a weather tight rubber-like seal. it conforms to the performance requirements of bs 5889 (a). Benefits
- faster curing than conventional low mod sealants.
-extremely low dirt pick up.
-flexible
- movement accommodation of +/- 35%.
-waterproof seal
- contains a powerful anti fungal compound to prevent mould growth.
areas for use
-sealing around pvcu profile, trim & cladding.
-perimeter pointing to pvcu, timber & metal window & door frames.*
-weathersealing to pre-formed panels & formwork.
- glass to glass & glass to aluminium weathersealing.
-cap glazing & remedial glazing sealing.
-general draughtproofing.
* not for use in conjunction with bitumen, or asphalt. use weathermate silicone
* do not use on lead or soft metals. use lead mate silicone.
* on highly porous surfaces such as new concrete, priming is advised or use silicone 450.
* not for use on substrates that may bleed oils, solvent or plasticisers.
* do not use in the vicinity of, or in conjunction with the edge sealant of double glazed units. use silicone 450.
* use on upvc & plastic components: due to the wide variety & quality of these materials, the user must always carry out an adhesion test prior to use. for optimum adhesion, use silicone 600 or silicone 450. thermal movement of pvc-u frames can be excessive. this product accommodates movement of +/- 35% of the joint width. for a higher movement factor use silicone 600 or silicone 450. when perimeter pointing to g.g.f standards, use only silicone 450 neutral cure.
* overpainting is not possible, so on applications where overpainting is required, use weather mate isoacrylic sealant (external only) or mirror mate (internal or external use).



















...

The Everbuild Range of EVERFLEX SILICONE 335 Construction sealants are 310ml sized cartridges, that are available in 5 colours, brown, white, transparent, grey & black. All these colours will fit most common mastic or sealant guns. 355 is a low modulus, reactive curing silicone sealant that cures quickly to reduce dirt pick up. ...

Everflex silicone 335 construction is a low modulus, reactive curing silicone sealant that cures quickly to reduce dirt pick up. it remains permanently flexible, forming a weather tight rubber-like seal. it conforms to the performance requirements of bs 5889 (a). Benefits
- faster curing than conventional low mod sealants.
-extremely low dirt pick up.
-flexible
- movement accommodation of +/- 35%.
-waterproof seal
- contains a powerful anti fungal compound to prevent mould growth.
areas for use
-sealing around pvcu profile, trim & cladding.
-perimeter pointing to pvcu, timber & metal window & door frames.*
-weathersealing to pre-formed panels & formwork.
- glass to glass & glass to aluminium weathersealing.
-cap glazing & remedial glazing sealing.
-general draughtproofing.
* not for use in conjunction with bitumen, or asphalt. use weathermate silicone
* do not use on lead or soft metals. use lead mate silicone.
* on highly porous surfaces such as new concrete, priming is advised or use silicone 450.
* not for use on substrates that may bleed oils, solvent or plasticisers.
* do not use in the vicinity of, or in conjunction with the edge sealant of double glazed units. use silicone 450.
* use on upvc & plastic components: due to the wide variety & quality of these materials, the user must always carry out an adhesion test prior to use. for optimum adhesion, use silicone 600 or silicone 450. thermal movement of pvc-u frames can be excessive. this product accommodates movement of +/- 35% of the joint width. for a higher movement factor use silicone 600 or silicone 450. when perimeter pointing to g.g.f standards, use only silicone 450 neutral cure.
* overpainting is not possible, so on applications where overpainting is required, use weather mate isoacrylic sealant (external only) or mirror mate (internal or external use).



















...

The Everbuild Range of EVERFLEX SILICONE 335 Construction sealants are 310ml sized cartridges, that are available in 5 colours, brown, white, transparent, grey & black. All these colours will fit most common mastic or sealant guns. 355 is a low modulus, reactive curing silicone sealant that cures quickly to reduce dirt pick up. ...

Everflex silicone 335 construction is a low modulus, reactive curing silicone sealant that cures quickly to reduce dirt pick up. it remains permanently flexible, forming a weather tight rubber-like seal. it conforms to the performance requirements of bs 5889 (a). Benefits
- faster curing than conventional low mod sealants.
-extremely low dirt pick up.
-flexible
- movement accommodation of +/- 35%.
-waterproof seal
- contains a powerful anti fungal compound to prevent mould growth.
areas for use
-sealing around pvcu profile, trim & cladding.
-perimeter pointing to pvcu, timber & metal window & door frames.*
-weathersealing to pre-formed panels & formwork.
- glass to glass & glass to aluminium weathersealing.
-cap glazing & remedial glazing sealing.
-general draughtproofing.
* not for use in conjunction with bitumen, or asphalt. use weathermate silicone
* do not use on lead or soft metals. use lead mate silicone.
* on highly porous surfaces such as new concrete, priming is advised or use silicone 450.
* not for use on substrates that may bleed oils, solvent or plasticisers.
* do not use in the vicinity of, or in conjunction with the edge sealant of double glazed units. use silicone 450.
* use on upvc & plastic components: due to the wide variety & quality of these materials, the user must always carry out an adhesion test prior to use. for optimum adhesion, use silicone 600 or silicone 450. thermal movement of pvc-u frames can be excessive. this product accommodates movement of +/- 35% of the joint width. for a higher movement factor use silicone 600 or silicone 450. when perimeter pointing to g.g.f standards, use only silicone 450 neutral cure.
* overpainting is not possible, so on applications where overpainting is required, use weather mate isoacrylic sealant (external only) or mirror mate (internal or external use).



















...