With its low profile design, you can use the Mini TT1 Transmitter on camera to trigger remote i-TTL / CLS speedlights or studio flashes attached to Flex TT5 Transceivers. Place TTL or manual flashes anywhere to illuminate the scene: Around corners, out-of-sight & in bright sunlight. The Mini TT1 is compatible with any Pocket Wizard radio for triggering manual flash or remote cameras. Control TL® Pocket Wizard’s newest firmware platform taps into the camera’s digital communications to enable an entirely new level of remote flash capability through our proven radio system. Control TL allows remote i-TTL for Nikon CLS / i-TTL systems as well as Manual Power Control. Control TL firmware is configurable & upgradeable for “future-proof” continuous improvement. Dedicated CLS / i-TTL Triggering Locking your Mini TT1 Transmitter into the hot shoe of a Nikon DSLR camera, & mounting CLS / i-TTL flashes onto Flex TT5 Transceivers gives you full flash exposure control with the freedom & reliability of a Pocket Wizard radio. There are no special settings to make or modes to call up. Use the camera’s flash exposure controls for basic control of remote flashes, or add an AC3 Zone Controller or Nikon Master unit for even more flexibility. Manual Power Control Adjust the manual power settings of your remote Nikon Speedlights directly from a AC3 Zone Controller, SB-800 or SB-900 flash mounted on your on-camera Mini TT1 or Flex TT5. You can independently control the power output of up to three remote groups of lights (you can have as many lights in each group as you want) from full power down to the lowest setting simply through the user interface on the back of the SB-800 or SB-900 or with the dials of the AC3 Zone Controller. Now you can work with total control with your remote lights, without leaving your shooting position. Nikon SU-800 Wireless Speedlight Commander may also be used. High Speed Sync (Auto FP) The Mini TT1 makes Nikon's FP/HSS mode a lot more functional with the freedom of radio. Now you can use your i-TTL speedlights in FP sync all the way to 1/8000 in the middle of the day in bright sun! Control TL gains faster recycling times & more flashes per set of batteries when shooting in Nikon's FP / HSS Flash mode. Use this feature to shoot wide open in bright sun for amazing results. Auto Trigger Select for Control TL The hot shoe on both the Mini TT1 & Flex TT5 will trigger just about any hot shoe flash placed into it in addition to the Nikon Speedlight's it is designed for. Yes, you can now fire just about any hot shoe flash including Vivitar, Canon, etc., in manual mode only & not TTL mode.  Hyper Sync™: Our patent pending Hyper Sync technology allows photographers to achieve faster X-sync speeds, sometimes up to 1/8000 of a second, with full power flash. Now you can cut the ambient light & use wide-open apertures, outdoors in bright sunlight. Hyper Sync automatically adjusts the timing of your flash trigger so that faster than X-sync speeds can be achieved. With certain Canon camera & flash combinations, you can achieve sync all the way to 1/8000th of a second. Just imagine what you can do using flash in bright sun with wide open apertures & fast shutter speeds. Since Hyper Sync is a trigger function you can use any Pocket Wizard Receiver including the Flex TT5, Plus II or Multi MAX. Hyper Sync works with both TTL speedlites & full size studio flash. Please visit https://wiki.pocketwizard.com/hyper Syncfor configuring Hyper Sync. While performance varies by the camera & flash equipment being used, Hyper Sync will get the maximum possible out of any set-up. Hyper Sync™ Automation With Control TL Firmware Update 3.0 (Nikon) & 6.0 (Canon), configuring Hyper Sync has now been automated. Hyper Sync Automation adjusts Hyper Sync timing in two separate places – on the transmitter & on the receiving Control TL radio. The transmitting or on-camera Mini TT1 or Flex TT5 automatically adjusts Hyper Sync to compensate for changes made to shutter speed. Photographers can further refine Hyper Sync via the Pocket Wizard Utility. For more information on Configuring Hyper Sync Automation, visit the Hyper Sync section of the Pocket Wizard Wiki. High Speed Sync (HSS / FP Sync) Disable Mode Select either HSS Sync or Hyper Sync™ at shutter speeds above x-sync. This means that you can use Hyper Sync & the benefit of full power flash all the way up to 1/2000 with certain flash systems. Rear Curtain Sync Precise rear curtain sync capability is engaged using the camera's sync settings. Capture natural light trails with sharp exposures at the end – no “after trails!” Pre-Flash Boost Nikon flashes use a dual preflash system to calculate i-TTL exposure values. In many TTL situations, including shooting in full sun, over long distance or using diffusers or bounce flash, the normal pre-flash is simply not enough for the camera to see. Pocket Wizard's Pre-Flash Boost increases your remote Nikon flashes first preflash by three stops &, if necessary, the second preflash by one stop. The boost level can also be adjusted at the flash if necessary. Power Tracking When working with certain manual flashes, you can change any of your settings on your camera & the system adjusts for those changes. Change your camera's exposure compensation to adjust the flash output, or make adjustments in aperture or ISO & the system balances your flash for proper exposure. Built-in Hot Shoe Lock your Nikon flash into the Mini TT1’s dedicated hot shoe & combine your remote flash with on-camera flash or use the on-camera flash for additional CLS / i-TTL or Manual Power Control only. The metal & glass reinforced resin hot shoe assembly is a superstructure onto itself & incredibly durable. The best part; no more cords. Basic Trigger Mode Allows the Mini TT1 or Flex TT5 to work as a transmitter on ANY camera it will fit. Anyone looking for the small form factor of the Mini TT1 can use it on other DSLR’s, SLR’s or even medium format cameras with standard hot shoes. Pocket Wizard Compatible The Mini TT1 sends out two trigger signals; one on the new Control TL channels, & another on the same channels as all standard trigger Pocket Wizard radios so they will work with any unit you may already have. Pocket Wizard Utility
- Programmable & Upgradeable Use the supplied Pocket Wizard Utility software with the on-board USB (Universal Serial Bus) port to program the Mini TT1 to any Pocket Wizard channel & zone as well as many other custom settings. The Mini TT1 can be upgraded whenever updates & feature enhancements are available. Channels / Learn Mode The Mini TT1 has two channel configuration settings; C1 & C2. Each can be programmed as needed with up to 20 Control TL channels* for TTL photography or Manual Power Control, or 32 standard channels** for manual flash photography. Channels can be configured with the Pocket Wizard utility or use the Learn function to quickly program channels, or the reset function to configure back to factory settings.*- 20 Control TL channels for FCC/IC 344 MHz radios & three Control TL channels for CE 433 MHz radios.**
- 32 Standard channels for FCC/IC 344 MHz radios & 35 Standard channels for CE 433 MHz radios. Zone Control Add the AC3 Zone Controller on top of your Mini TT1 for Nikon & gain three zones of power control right from the camera’s position. Works in both auto/CLS/i-TTL & manual. Shut down an entire zone with the flick of a switch.AC3 Zone Controller sold separately. Speed Cycler with an AC3 Zone Controller Previously only seen with Pocket Wizard’s Multi MAX radios, this new mode is designed to rapidly cycle through multiple flash units fired individually in sequence. This allows photographers to fire a camera in sync with flashes faster than a single flash unit can recycle. It can also be used for triggering remote cameras sequentially. Speed Cycler is engaged on a transmitting Mini TT1 or Flex TT5 via the Pocket Wizard Utility. Speed Cycler mode requires an AC3 Zone Controller in the top hot-shoe of the on-camera Pocket Wizard radio. Zones A, B, & C will be triggered sequentially & individual zones can be disabled by setting the AC3’s Zone Switch to the off position. Both TTL & manual flash controls are supported. Flash Power Control without a Camer A Photographers can now take their AC3 & transmitting radio off-camera & use it to set power levels for any flash with a Control TL receiver, making it more convenient to use an optically triggered light meter, or control the power levels with just a Mini TT1/ Flex TT5 & AC3 in their hand while another photographer takes the pictures. Previously, an AC3 Zone Controller on a Mini TT1 or Flex TT5 needed to be on camera to send manual power levels to remote flashes. Now, when connected to a Mini TT1 or Flex TT5, manual power levels are transmitted to remote flashes when the TEST button is pressed even when the transmitter is off the camera. This affects both speedlights connected to receiving Flex TT5s & larger flashes like Alien Bees & Elinchrom RX units with Control TL receivers. Continuous Fast FPS Never before have you been able to shoot remote CLS / i-TTL non-stop in continuous high-speed mode. Fill the buffer! Nothing else comes close. Low-Profile Design The lay-flat design with integrated hot shoe & internal antenna keeps a very low profile on your camera. Powered by a CR2450 lithium coin cell battery.

...

With its low profile design, you can use the Mini TT1 Transmitter on camera to trigger remote E-TTL speedlites or studio flashes attached to Flex TT5 Transceivers. Place TTL or manual flashes anywhere to illuminate the scene: Around corners, out-of-sight & in bright sunlight. The Mini TT1 is compatible with any Pocket Wizard radio for triggering manual flash or remote cameras. Control TL™ Pocket Wizard’s firmware platform taps into the camera’s digital communications to enable an entirely new level of remote flash capability through our proven radio system. Control TL allows remote TTL for Canon E-TTL II systems as well as Manual Power Control. Control TL firmware is configurable & upgradeable for “future-proof” continuous improvement. Find more details on Control TL here. Dedicated E-TTL II Triggering Locking your Mini TTI Transmitter into the hot shoe of a Canon DSLR camera & mounting E-TTL II flashes onto Flex TT5 Transceivers gives you full autoflash exposure control with the freedom & reliability of a Pocket Wizard radio. There are no special settings to make or modes to call up. Use the camera, on-camera flash or flash commander controls for flash compensation, zone & ratio control. Manual Power Control Adjust the manual power settings of your remote Canon Speedlites directly from a AC3 Zone Controller, 580EX or 580EX II flash mounted on your on-camera Mini TT1 or Flex TT5. You can independently control the power output of up to three remote groups of lights (you can have as many lights in each group as you want) from full power down to the lowest setting simply with the dials of the AC3 Zone Controller or the user interface on the back of the 580 EX or 580 EX II flash. Manual Power Control also works with select studio lights when paired with Power ST4, Power MC2, or AC9/ Flex TT5. Now you can work with total control with your remote lights, without leaving your shooting position. Optimized HSS High Speed Sync takes Speedlite flash photography all the way to 1/8000th of a second sync. Control TL optimizes this amazing Canon feature & provides more light (which equals greater working distance), faster recycling times & more flashes per battery set when shooting in Canon's HSS/FP Flash mode. Use this feature to shoot wide open in bright sun for amazing results. Click here to watch a detailed video on Optimized High Speed Sync as narrated by Photographer Mark Wallace. Hyper Sync™ Our patent pending Hyper Sync technology allows photographers to achieve faster X-sync speeds, sometimes up to 1/8000 of a second, with full power flash. Now you can cut the ambient light & use wide-open apertures, outdoors in bright sunlight. Hyper Sync automatically adjusts the timing of your flash trigger so that faster than X-sync speeds can be achieved. With certain Canon camera & flash combinations, you can achieve sync all the way to 1/8000th of a second. Just imagine what you can do using flash in bright sun with wide open apertures & fast shutter speeds. Since Hyper Sync is a trigger function you can use any Pocket Wizard Receiver including the Flex TT5, Plus II or Multi MAX. Hyper Sync works with both TTL speedlites & full size studio flash. Please visit https://wiki.pocketwizard.com/hyper Sync for configuring Hyper Sync. While performance varies by the camera & flash equipment being used, Hyper Sync will get the maximum possible out of any set-up. Hyper Sync™ Automation With Control TL Firmware Update 3.0 (Nikon) & 6.0 (Canon), configuring Hyper Sync has now been automated. Hyper Sync Automation adjusts Hyper Sync timing in two separate places – on the transmitter & on the receiving Control TL radio. The transmitting or on-camera Mini TT1 or Flex TT5 automatically adjusts Hyper Sync to compensate for changes made to shutter speed. Photographers can further refine Hyper Sync via the Pocket Wizard Utility. For more information on Configuring Hyper Sync Automation, visit the Hyper Sync section of the Pocket Wizard Wiki. High Speed Sync (HSS or FP Sync) Disable Mode Select either HSS Sync or Hyper Sync™ at shutter speeds at or over 1/640. This means that you can use Hyper Sync & the benefit of full power flash all the way up to 1/8000 with certain flash systems. Optimized Rear Curtain Sync Precise rear curtain sync capability is engaged automatically, no buttons to press. Set the shutter speed at which rear curtain sync is engaged with the Pocket Wizard Utility. Capture natural light trails with sharp exposures at the end – no “after trails!” Pre-Flash Boost In some E-TTL situations, including shooting in full sun, over long distance or using diffusers or bounce flash, the normal pre-flash is simply not enough for the camera to see. With Pre-Flash Boost, the pre-flash is two stops brighter. This will Approx. double the working distance of E-TTL II, compensating for the light loss when defusing or bouncing. Power Tracking When working with the Power ST4, Power MC2 & AC9/ Flex TT5 paired with compatible manual flashes, you can change any of your settings on your camera & the system adjusts for those changes. Change your exposure compensation to adjust the exposure or make adjustments in aperture or ISO & the system balances your flash for proper exposure. Zone Control Add the AC3 Zone Controller on top of your Mini TT1 & gain three zones of power control right from the camera’s position. Works in both auto/E-TTL II & manual. Shut down an entire zone with the flick of a switch. Speed Cycler with an AC3 Zone Controller Previously only seen with Pocket Wizard’s Multi MAX radios, this new mode is designed to rapidly cycle through multiple flash units fired individually in sequence. This allows photographers to fire a camera in sync with flashes faster than a single flash unit can recycle. It can also be used for triggering remote cameras sequentially. Speed Cycler is engaged on a transmitting Mini TT1 or Flex TT5 via the Pocket Wizard Utility. Speed Cycler mode requires an AC3 Zone Controller in the top hot-shoe of the on-camera Pocket Wizard radio. Zones A, B, & C will be triggered sequentially & individual zones can be disabled by setting the AC3’s Zone Switch to the off position. Both TTL & manual flash controls are supported. Flash Power Control without a Camera Photographers can now take their AC3 & transmitting radio off-camera & use it to set power levels for any flash with a Control TL receiver, making it more convenient to use an optically triggered light meter, or control the power levels with just a Mini TT1/ Flex TT5 & AC3 in their hand while another photographer takes the pictures. Previously, an AC3 Zone Controller on a Mini TT1 or Flex TT5 needed to be on camera to send manual power levels to remote flashes. Now, when connected to a Mini TT1 or Flex TT5, manual power levels are transmitted to remote flashes when the TEST button is pressed even when the transmitter is off the camera. This affects both speedlights connected to receiving Flex TT5s & larger flashes like Alien Bees & Elinchrom RX units with Control TL receivers. Continuous Fast FPS Radios work a lot fast then infrared communications allowing you to shoot with remote flash in E-TTL as speeds close to your maximum frames per second. Never before have you been able to shoot remote E-TTL non-stop in continuous high-speed mode. Fill the buffer! Nothing else comes close. Built-in Hot Shoe Lock your Canon flash into the Flex TT5’s dedicated hot shoe & combine your remote flash with on-camera flash or use the on-camera flash for additional E-TTL II or Manual Power Control only. The metal & glass reinforced resin hot shoe assembly is a superstructure onto itself & incredibly durable. The best part; no more cords. Basic Trigger Mode Allows the Mini TT1 or Flex TT5 to work as a transmitter on ANY camera it will fit. Anyone looking for the small form factor of the Mini TT1 can use it on other DSLR’s, SLR’s or even medium format cameras with standard hot shoes. The Mini TT1 & Flex TT5 are completely reverse compatible with all previous Pocket Wizards so they will work with whatever Pocket Wizards you already own. Pocket Wizard Compatible The Mini TT1 operates on the same channels as all other Pocket Wizards & will work with any unit you may already have. Pocket Wizard Utility
- Programmable & Upgradeable Use the supplied Pocket Wizard Utility software with the on-board USB (Universal Serial Bus) port to program the Mini TT1 to any Pocket Wizard channel & zone as well as many other custom settings. The Mini TT1 can be upgraded whenever updates & feature enhancements are available (many planned!). Channels / Learn Mode The Mini TT1 has two channel configuration settings; C1 & C2. Each can be programmed as needed with up to 20 Control TL channels* for TTL photography or Manual Power Control, or 32 standard channels** for manual flash photography. Channels can be configured with the Pocket Wizard utility or use the Learn function to quickly program channels, or the reset function to configure back to factory settings.*
- 20 Control TL channels for FCC/IC 344 MHz radios & three Control TL channels for CE 433 MHz radios.**
- 32 Standard channels for FCC/IC 344 MHz radios & 35 Standard channels for CE 433 MHz radios. Automatic HSS Trigger Timing for Manual Flash This means that you can mix a manual flash with an E-TTL II flash in HSS/FP Sync shots at 1/640 & above with certain flash systems. Auto Trigger Select for Control TL The hot shoe on both the Mini TT1 & Flex TT5 will trigger just about any hot shoe flash placed into it in addition to the Canon Speedlite’s it is designed for. Yes, you can now fire just about any hot shoe flash including Vivatar, Nikon, etc., in manual mode only & not TTL mode. (max trigger voltage < 50V, use P2 port for up to 200V) Low-Profile Design The Mini TT1 Transmitter is the smallest Pocket Wizard ever, utilizing an internal antenna & common coin-cell battery. At just 2.3oz (65 grams) you barely realize it’s on the camera. Power Saver The Mini TT1 Transmitter will go to sleep 10 seconds after your camera does to conserve energy. Just touch the shutter button half way to wake both the camera & the Mini TT1. It works on the supplied CR2450 coin cell battery (or optional CR2354 for in the field options) that provide hundreds of hours of battery life.


...

Optech Mirrorless Camera Strap
- Black The Mirrorless Strap from OP/TECH USA is designed to accommodate cameras that are larger
...

Phottix Mitros Flash Bag The perfect heavy duty bag for Phottix Mitros or other brand flashes. With belt attachment & three pockets for storing cables & other items. ...

Phottix Mitros+ & Odin Scott Kelby Kit for Canon • Built-In Odin • Transmitter/ Receiver • Compatible with manufacturer TTL • Guide Number: 190' at ISO 100 & 105mm • Zoom Range: 24-105mm (14mm with Panel) • Tilts from -7° to +90° • Rotates Left & Right 180° • Wireless Master/ Slave TTL Functionality • Recycle Time: 0.1-5 Seconds • High-Speed, 1st & 2nd Curtain Sync • Runs on 4 AA Batteries The Scott Kelby Mitros+ TTL Flash & Odin TCU TTL Flash Trigger Kit for Canon from Phottix features the Mitros+ TTL flash for Canon, the Odin TCU TTL flash trigger, 10" flash softbox with strap, a 36" Double-Small white shoot-through umbrella, Varos II multi-function flash shoe umbrella holder, a 6. 6 pound Stay-Put Sandbag II, a 28" gear bag, & a 6. 5' 5-section compact light st&. This gives you a wide variety of tools & accessories for advanced off-camera flash photography. ...

Phottix Mitros+ Odin Combo for Nikon Quick facts: • Built-In Odin • Transmitter/ Receiver • Compatible with manufacturer TTL • Guide Number: 190' at ISO 100 & 105mm • Zoom Range: 24-105mm (14mm with Panel) • Tilts from -7° to +90° • Rotates Left & Right 180° • Wireless Master/ Slave TTL Functionality • Recycle Time: 0.1-5 Seconds • High-Speed, 1st & 2nd Curtain Sync • Runs on 4 AA Batteries" The Mitros+ TTL Flash & Odin Flash Trigger Combo for Nikon Cameras from Phottix is a versatile kit that pairs a full-size Nikon compatible on-camera flash with a wireless transmitter able to trigger & control TTL & manual flash exposure on up to 3 groups of flash units from distances up to 328'. The Mitros+ TTL Flash is a powerful unit with Nikon i-TTL functionality. The Mitros+ features a guide number of 190' at ISO 100 & a zoom range of 24 to 105mm. Besides receiving radio signals, the Mitros+ can also transmit them to other units via its built-in transmitter. The Odin TCU TTL Flash Trigger is a wireless transmitter that runs on the 2. 4 GHz frequency, has 4 channels with 3 groups & can fire the Mitros+ or other compatible flash from a distance of 328'. Flashes within each group have +/- 3 EV power compensation in TTL or user-determined power levels in manual mode. The transmitter can also remotely adjust the angle of the flash beam via its zoom button. The Odin is compatible with Phottix Odin Tx, Odin Rx, Strato II Rx, OP Tx (master), OP Rx (slave) & OP (slave) wireless systems. ...

Phottix Mitros+ TTL Transceiver Flash for Canon The Phottix Mitros+ TTL Transceiver Flash is the best of Phottix’s gold-standard products all-in-one. A flash with Phottix Odin Transmitter & Receiver, & Strato receiver all built in.

Features: GN: 58 Canon-Compatible TTL Flash Built-in: Phottix Odin Transmitter & Receiver, & Strato II Receiver Optical Slave Canon-compatible Master/ Slave IR Triggering Modes ETTL I/II, Manual & Multi Stroboscopic Modes High Speed Sync & Second Curtain Sync AF Assist Light Flash Zoom: 24-105mm External Battery Port, 3.5mm Sync Port Quick Flash Mode The Phottix Mitros+ TTL Transceiver Flash is the best of Phottix’s gold-standard products all-in-one. What’s the + ? + Built-in Odin Transmitter + Built-in Odin Receiver + Built-in Strato Receiver + Memory Functions The Phottix Mitros is a powerful & durable hot shoe flash that has proven popular since it’s release earlier this year. The Phottix Mitros+ adds significant functionality, allowing photographers to not only use the Mitros on or off camera for lighting, but to also control & trigger remote flash by radio signal. The Mitros+ is an industry landmark & was developed with input from wedding & event photographers. Use the Mitros+ on-camera as a key or fill light, as well as control & trigger other Mitros+ flashes or compatible flashes using Phottix Odin Receivers. The Mitros+ also offers a built-in Phottix Odin Receiver & Strato II Receiver. Existing Phottix triggers, like the Phottix Odin or Strato II can be used to trigger the Mitros+ without extra receivers. Odin Functionality With the Phottix Odin’s functionality built-in the Mitros+ can be used to trigger Phottix Odin & Strato Receivers. Likewise: you can also trigger the Mitros+ using a Phottix Odin TCU or Strato II Multi Transmitter. Using the Mitros+ in Odin Transmitter Mode provides the same functions found on the Phottix Odin, including: Remote power control of groups in TTL with +/- EV adjustments (3 stops in 1/3 stop increments
- 18 different levels) Remote power control in Manual Mode: Full power to 1/128 in 1/3 stop increments. Mix TTL & Manual flash – fire some groups in TTL, others as manual. Remote power control in A:B ratio modes with +/- EV adjustments. High speed sync – shutter speeds up to 1/8000 sec. Second curtain sync functions. Remote flash head zoom adjustments – auto or manual The Mitros+ will control & trigger other Mitros+ flashes in receiver mode or Phottix Odin Receivers. Like the Phottix Odin, the Mitros+ with a backlit LCD, is intuitive, & easy to use & underst&. Strato Functionality The Mitros+ has a built-in Strato II Multi-compatible receiver. Existing Strato II Multi transmitter can trigger the Mitros+. The Mitros+ can also trigger Strato II Multi & Strato I Receivers when set in Odin Transmit Mode. Memory Functions New with the Mitros+, built-in three location memory save & retrieval functions. Flash set up & custom function information can be saved in the Mitros+’s memory & be quickly recalled when needed. Use the Mitros+ in different modes for different situations? Quickly recall saved set-ups for fast use.


...

Phottix Mitros+ TTL Transceiver Flash for Nikon The Phottix Mitros+ TTL Transceiver Flash is the best of Phottix’s gold-standard products all-in-one. A flash with Phottix Odin Transmitter & Receiver, & Strato receiver all built in.

Features: GN: 58 Nikon-Compatible TTL Flash Built-in: Phottix Odin Transmitter & Receiver, & Strato II Receiver Optical Slave Nikon-compatible Master/ Slave IR Triggering Modes TTL, Manual & Multi Stroboscopic Modes High Speed Sync & Second Curtain Sync AF Assist Light Flash Zoom: 24-105mm External Battery Port, 3.5mm Sync Port Quick Flash Mode The Phottix Mitros+ TTL Transceiver Flash is the best of Phottix’s gold-standard products all-in-one. What’s the + ? + Built-in Odin Transmitter + Built-in Odin Receiver + Built-in Strato Receiver + Memory Functions The Phottix Mitros is a powerful & durable hot shoe flash that has proven popular since it’s release earlier this year. The Phottix Mitros+ adds significant functionality, allowing photographers to not only use the Mitros on or off camera for lighting, but to also control & trigger remote flash by radio signal. The Mitros+ is an industry landmark & was developed with input from wedding & event photographers. Use the Mitros+ on-camera as a key or fill light, as well as control & trigger other Mitros+ flashes or compatible flashes using Phottix Odin Receivers. The Mitros+ also offers a built-in Phottix Odin Receiver & Strato II Receiver. Existing Phottix triggers, like the Phottix Odin or Strato II can be used to trigger the Mitros+ without extra receivers. Odin Functionality With the Phottix Odin’s functionality built-in the Mitros+ can be used to trigger Phottix Odin & Strato Receivers. Likewise: you can also trigger the Mitros+ using a Phottix Odin TCU or Strato II Multi Transmitter. Using the Mitros+ in Odin Transmitter Mode provides the same functions found on the Phottix Odin, including: Remote power control of groups in TTL with +/- EV adjustments (3 stops in 1/3 stop increments
- 18 different levels) Remote power control in Manual Mode: Full power to 1/128 in 1/3 stop increments. Mix TTL & Manual flash – fire some groups in TTL, others as manual. Remote power control in A:B ratio modes with +/- EV adjustments. High speed sync – shutter speeds up to 1/8000 sec. Second curtain sync functions. Remote flash head zoom adjustments – auto or manual The Mitros+ will control & trigger other Mitros+ flashes in receiver mode or Phottix Odin Receivers. Like the Phottix Odin, the Mitros+ with a backlit LCD, is intuitive, & easy to use & underst&. Strato Functionality The Mitros+ has a built-in Strato II Multi-compatible receiver. Existing Strato II Multi transmitter can trigger the Mitros+. The Mitros+ can also trigger Strato II Multi & Strato I Receivers when set in Odin Transmit Mode. Memory Functions New with the Mitros+, built-in three location memory save & retrieval functions. Flash set up & custom function information can be saved in the Mitros+’s memory & be quickly recalled when needed. Use the Mitros+ in different modes for different situations? Quickly recall saved set-ups for fast use.


...

Phottix Mitros+ TTL Transceiver Flash for Nikon Kit The Mitros+ Kit

Includes:: a Phottix Reflective Studio

...

Manfrotto MK055XPRO3 Tripod & XPRO Ball Head With 200PL Plate This 055 kit comprises a 055XPRO3 3-section aluminium tripod & a portable, versatile ball head. Both tripod & head have advanced features & excellent build quality. The key feature of this kit is the tripod's 90° centre column mechanism, which allows the column to be extended vertically as normal or horizontally. This makes it an extremely versatile tripod, suitable for a wide range of photography applications. The horizontal column mechanism is housed within the tripod's top casting for compactness, but it is easily & quickly extended whenever you need it. Switching between vertical & horizontal column orientation requires no disassembly, & can even be done with a camera attached. The legs of the tripod are also fast to extend & adjust, thanks to the Quick Power Lock levers that block & unblock each leg section. The special design of the QPL levers allow a stronger & more comfortable single-handed leg lock grip. The sections of each leg on the tripod can be released from their folded position in a single movement. The QPL lever design also offers more powerful locking of each section, making this tripod more stable & rigid than traditional lever design models. Intuitive, ergonomic leg angle selectors allow each leg to be independently & solidly set to any of the preset angles, afford considerably greater positioning freedom. A bubble level is built in to the top of the centre column for precise framing. The bubble level rotates freely around the centre column, so it can be positioned wherever it's easiest for you to see while you adjust the tripod & without it either being obscured by the mounted head & camera. The tripod’s top casting has an Easy Link connector to support a photo or video accessory (such as an LED light, flash, reflector, or other piece of equipment) on an extending arm or bracket, & transforming it into a practical mobile studio. The new XPRO Ball Head is the perfect union between innovative solutions & design. It has a new triple locking system which guarantees camera position stability, friction control helping the user balance the weight of camera equipment & two levelling bubbles to precisely frame composition. Moreover, its new polymer rings have substituted that unpleasant, messy grease, ensuring smooth, accurate & less jerky camera movement. XPRO Ball Head is portable, lightweight & reliable thanks to its magnesium body & comes with the Manfrotto 200 pl plate. The 055XPRO3 & the MHXPRO-BHQ2 head are made in Italy by Manfrotto. ...