Spare or replacement battery for the Explorer 1500 battery generator. ...

The best choice for DSLR or for lightweight camcorders. Recommended for lenses up to 300mm maximum. Series 2 offers an excellent maximum load capacity & very good torsional rigidity. Weight & size are convenient for travelling or trekking. Available in 3- & 4-section models at standard heights. Series 2 is the ideal solution for photographers that are looking for a solid & yet lightweight tripod. Gitzo have introduced a new Anti Leg Rotation system, which means the tripod can be opened in less than 15 seconds. Simply loosen all the twist locks on each leg at the same time, then pull the leg down & tighten the locks individually. The system consists of two pins, one fixed & one manually operated by means of a button, that prevent camera equipment from suddenly dropping out of the head when the quick release locking knob is released. Extremely useful with heavy equipment, long lenses & spotting scopes. By fine tuning the freedom of movement of the head, friction control makes the head slower & more precise or faster & looser. This feature also helps to make using heavy equipment or long lenses safer. On ball & fluid head models without separate friction controls, slowly adjusting the lock knobs gives similar results. G-Lock is the new Gitzo leg locking system. The locking mechanism has been completely redesigned in order to achieve a 20% increase in rigidity, faster operation & stronger, safer locking. G-Lock’s special design also provides a “gravity lock” effect: the higher the load applied vertically to the leg, the stronger the lock. This new feature means that you can remove the center column to save weight & get the camera closer to the ground. Uses existing components: the upper disc with reversible 1/4
- 3/8 bolt & the column hook assembly: Remove column & fix the disk directly to the upper casting using the column hook. No tools needed. HOOK
- This built-in accessory means that you can hang a stabilizingweight (e.g. a full camera bag or a sand/water bag) fromthe bottom of the tripod center column. Useful with longheavy lenses, on uneven ground or in windy conditions. All tripods & monopods in Series 1 & above are provided with removable rubber feet. This feature means that you can easily change worn out rubber feet or to fit other accessories, such as spiked feet or snow/sand shoes. (4 sections tripods in Series 1 are excluded because the final leg section is too narrow to fit these ends). The new leveling system made from three independent leveling bubbles on the quick release plate & one in the ball stem, always guarantee perfectly leveled images. The problem that affects many high quality heads in the market regarding drift angle is absolutely minimized with an outstanding value of 0, 03°. The center column locking collar above the tripod shoulder makes it easier to adjust the column quickly. Series 1 & above are built with an anti-rotation grooved center column for enhanced stability. The rapid column can easily be inverted for an alternative shooting angle or low level macro work. Handles can removed & repositioned or rotated in different positions. This feature greatly increases a head’s versatility & is particularly appreciated by left handed users. Safe Grip is a material that gives a safer lock between your camera & the head plate, preventing the camera from moving or slipping. It is used on quick release plates & in applications where the camera equipment is screwed to the support to reduce pivoting & twisting. Safe Lock is a special techno polymer that maximises locking torque & equipment stabilisation. It is used on the upper discs of tripods & heads, & in applications where the equipment is rotated & screwed onto the support to eliminate micro movements & vibration. The new tripod upper disc is called “ Power Disc”. It is made from machined solid aluminum & it now features two locking screws, one to lock the head, the other to safely lock the disc onto the column. The “ Power Disc” gives a rock solid connection of the whole system for additional safety & stability. A fluid cartridge consists in a system made with two parts that slide one on the other. Inside the system is included a special fluid that controls the movement & makes it extremely soft, “fluid” & smooth. The cartridge’s inner design is very important & if well designed allows maximum movement control yet minimizes cartridge weight & size. Gitzo uses a special fluid that guarantees a consistent performance over a wide range of temperatures.

...

With this optional Sekonic test target you can create a unique exposure profile that can be loaded into the Sekonic L-758DR through its built-in USB (Universal Serial Bus) port. ...

Sekonic Exposure Profile Target 1 Version 2.0 & later of the Digital Transfer Software is designed to be used with Exposure Profile Targets that have alignment marks. The alignment marks simplify & automate the selection of Profile Target images with the DTS software. If you own a Profile Target I & do not have the alignment marks, please request directly from Sekonic USA by calling the Service Department at 914-347-3300. If you live outside the USA, contact your country's distributor. To profile your camera & lens combinations, the Exposure Profile Target I is fully compatible with FREE Data Transfer Software along with the L-758D, L-758DR, L-758 Cine, L-478D, & L-478DR light meters. The result is total exposure accuracy. Features exposure target on front, & gray card on back for custom white balance of D-SLRs. ...

This is a 25 patch test target that gathers more information about the camera’s exposure characteristics than the previous test target. It consists of two sides; an 18% grey card used to custom white balance digital cameras before profiling & on the other, a profile target consisting of a central 18% grey patch that is surrounded by 24 patches arranged in 1/6th stop values, making it successively brighter & darker. The Sekonic Exposure Profile Target II offers faster, more accurate testing as it requires only three shots to gather a wide range of exposure data from the camera’s imaging system. The first shot is made at the normal, metered exposure determined by a Sekonic L-758DR. The second shot is made at -3EV below the metered exposure & the third shot at +3EV above the metered exposure. The result is total exposure accuracy. ...

The easy-to-setup & use EFI e Xpress v 4.1 delivers high-quality color for your photo production, while letting photographers, like you, concentrate on their creative work. Check out a few of the key benefits this software RIP gives you: Saves you time & dramatically decrease mistakes: The solution automatically configures photos, collections (single- & multi-image templates) & contact sheets. It also processes routine tasks faster due to features such as color & printing presets, so you can do other things to grow your profits. Makes you more productive: e Xpress for Photo comes with simple production tools for cropping, rotating & crop mark support to help you generate more work. Lowers your operating costs & supports less experienced users: It improves media utilization & lessens waste through automation. This intuitive solution also comes with no learning curve, so even your beginners can use it right away. ...

attaches by.: type 1 + spigot art.013 female attachment type

Colour: black color gravity cast: yes length:

...

Mounts to Studio Clamp to hold lightweight fixtures or props. It is easily adjustable & holds its position without locking. Measures 8.87" (20cm) long, 0.5" (1.2cm) diameter, with a 5/8" hexagonal stud with a 3/8" female thread at one end & a 5/8" stud with a 1/4-20 male thread at the other end. ...

Bowens produces some of the most innovative, & advanced studio lighting systems available today. Bowens lighting equipment is used & trusted by professionals around the world. ...

Adds 15½" to crossarm. Mounts directly into arm & accepts any camera platform. Compatible with Cambo UBS & UST Studio Stands. ...