Add a USB (Universal Serial Bus) 3.0 port connection that inserts flush into a laptop Express Card slot. The ECUSB3S11 Flush Mount 1-Port USB (Universal Serial Bus) 3.0 Express Card lets you add a single USB (Universal Serial Bus) 3.0 port connection to your laptop through an Express Card slot. The USB (Universal Serial Bus) 3.0 adapter uses a unique form factor design that allows it to sit fully in a standard 34mm Express Card slot without sticking out. The port sits virtually flush with the sides of the laptop, enabling you to leave the card installed even while on the move, without fear of damage to the card or slot. Enhanced with UASP support (USB Attached SCSI Protocol), this USB (Universal Serial Bus) 3.0 controller performs up to 70% faster than conventional USB (Universal Serial Bus) 3.0 when paired with a UASP supported enclosure (Note: UASP requires a compatible operating system). Using a more efficient protocol than the traditional USB (Universal Serial Bus) BOT (Bulk-Only Transport), UASP technology optimizes transfers by allowing multiple commands to be processed simultaneously, significantly increasing transfer speeds for less wait time on data transfers. The USB (Universal Serial Bus) 3.0 Express Card adapter supports data transfer rates up to 5 Gbps, & is still backward compatible with USB (Universal Serial Bus) 2.0 at up to 480 Mbps, or USB (Universal Serial Bus) 1.1/1.0 at up to 12/1.5 Mbps respectively. UASP is supported in Windows 8, Server 2012 & Linux kernel 2.6.3 or later. In testing UASP performed with up to a 70% faster read / 40% faster write speed over traditional USB (Universal Serial Bus) 3.0 at peak performance. At the same peak in testing, UASP also showed up to an 80% reduction in required processor resources. Test results were obtained using an Intel Ivy Bridge system, Star Tech.com add-on USB (Universal Serial Bus) 3.0 cards, a UASP-enabled Star Tech.com enclosure, & a SATA III solid state drive. ...

The ICUSB2321F 1-Port USB (Universal Serial Bus) to Serial RS232 Adapter Cable with FTDI chipset & COM Retention converts an available USB (Universal Serial Bus) 1.1 or 2.0 port into an RS232 serial DB9 port to connect, monitor & control your serial devices. This compact adapter features COM retention, allowing the same COM port value to automatically be re-assigned to the port if the cable is disconnected & re-connected to the host computer, or if the system is rebooted. Unlike most of USB (Universal Serial Bus) to serial adapters, this one uses the FTDI chipset which supports additional customization, advanced features, & compatibility not necessarily offered by other solutions. Compatibility with a broad list of Operating Systems including Windows, Windows CE, Mac OS & Linux, makes this product easy to integrate into mixed environments. ...

The ICUSB2321F 1-Port USB (Universal Serial Bus) to Serial RS232 Adapter Cable with FTDI chipset & COM Retention converts an available USB (Universal Serial Bus) 1.1 or 2.0 port into an RS232 serial DB9 port to connect, monitor & control your serial devices. This compact adapter features COM retention, allowing the same COM port value to automatically be re-assigned to the port if the cable is disconnected & re-connected to the host computer, or if the system is rebooted. Unlike most of USB (Universal Serial Bus) to serial adapters, this one uses the FTDI chipset which supports additional customization, advanced features, & compatibility not necessarily offered by other solutions. Compatibility with a broad list of Operating Systems including Windows, Windows CE, Mac OS & Linux, makes this product easy to integrate into mixed environments. ...

Add an RS232 Serial Port with Circuit Isolation to your Laptop or Desktop Computer, through USB (Universal Serial Bus). The ICUSB2321FIS 1-Port FTDI USB (Universal Serial Bus) to Serial RS232 Adapter Cable with Optical Isolation converts an available USB (Universal Serial Bus) 1.1 or 2.0 port into an RS232 DB9 port that can be used to connect, monitor & control your serial devices. The USB (Universal Serial Bus) to serial adapter features integrated optical isolation circuits & surge protection to protect your critical, sensitive control equipment against electrical damage, making it a viable solution for costly industrial serial devices. The versatile FTDI chipset also supports COM retention, additional customization/features, & compatibility not offered by most other solutions. Broad operating system compatibility including Windows, Windows CE, Mac OS & Linux, makes this product easy to integrate into mixed environments. ...

Add an RS232 Serial Port with Circuit Isolation to your Laptop or Desktop Computer, through USB (Universal Serial Bus). The ICUSB2321FIS 1-Port FTDI USB (Universal Serial Bus) to Serial RS232 Adapter Cable with Optical Isolation converts an available USB (Universal Serial Bus) 1.1 or 2.0 port into an RS232 DB9 port that can be used to connect, monitor & control your serial devices. The USB (Universal Serial Bus) to serial adapter features integrated optical isolation circuits & surge protection to protect your critical, sensitive control equipment against electrical damage, making it a viable solution for costly industrial serial devices. The versatile FTDI chipset also supports COM retention, additional customization/features, & compatibility not offered by most other solutions. Broad operating system compatibility including Windows, Windows CE, Mac OS & Linux, makes this product easy to integrate into mixed environments. ...

The POEINJ1GI Industrial Gigabit Po E+ Injector provides power & data connectivity to a Gigabit Po E-compliant device over standard Ethernet cabling at distances of up to 330ft (100m), & offers redundant, wide-range DC power inputs. This injector means that you can easily connect a Po E-powered device (PD) to a non-Po E LAN switch, avoiding the cost of upgrading your switch to a Po E-enabled model. Providing seamless power failover in the event of power dips or failures, the injector features redundant 20-57V DC (nominal 24/48V DC) terminal block power inputs. The internal DC-DC converter provides the Po E injector with high voltage output from a low voltage input ( ...

Supply power & data connectivity to an individual Gigabit Po E device over standard Ethernet cabling. The POEINJ1G 1 Port Gigabit Power over Ethernet (Po E+) injector supplies power & data connectivity to a Gigabit Po E-compliant device over standard Ethernet cabling at distances of up to 100m (330ft). This single-port Po E injector means that you can easily connect an individual Po E-powered device (PD) to a non-Po E LAN switch, avoiding the cost of upgrading your switch to a Po E-enabled model. Fully compliant with IEEE 802.3at / 802.3af standards, the high-power Po E / PSE adapter provides a 10/100/1000 Mbps port with support for up to 48V (30W max) output. A perfect solution for applications where an electrical outlet may not be available, the injector adapter can be used to power Po E-enabled devices such as IP cameras or Wireless Access Points (WAPs). The compact, wall-mountable design makes it easy to install the adapter into areas where space is limited, & can be installed in seconds with no configuration required. ...

Deliver power & data to your Power over Ethernet device using this mountable Po E+ midspan. This Gigabit Power over Ethernet (Po E+) injector supplies power & data connectivity to a Gigabit Po E-compliant device using standard Ethernet cable, at distances of up to 100 m (330 ft.). The Po E midspan is a cost-effective alternative to upgrading your existing network switch to a Po E-capable model. This versatile Po E injector lets you connect a Po E-powered device (PD) to a non-Po E network switch, so you can avoid the expense & aggravation of replacing your existing switch with a Po E-enabled model. It supplies up to 30 watts of power, so you can easily power & access a high-power Po E-compliant device, such as an IP camera or a wireless access point (WAP), using traditional copper (RJ45) Ethernet cable. The midspan injector makes it easy to extend data & power connectivity to your Po E+ device across long distances, even in a remote location where a typical power outlet isn't available. You can integrate this compact injector discreetly into a variety of environments. It features a surface-mountable housing that's perfect for installing on walls or under a desk, but it's also palm-sized, for use on desktop surfaces. Plus, with plug-&-play operation, you can enjoy fast & hassle-free setup without disrupting your workflow. Not sure which class your Po E device is? The Gigabit Po E+ injector automatically detects the power requirements of your connected Po E PD, & delivers the appropriate level of power without damaging your device. ...

Remotely manage an industrial RS232 or RS422/485 serial device over an IP network, with redundant 10/100 Ethernet ports. The NETRS232485 Serial Device Server lets you remotely manage an industrial RS232/422/485 serial device over a local or wide area network (LAN/WAN), with redundant power inputs & dual 10/100 Mbps Ethernet ports. To minimize downtime, this intuitive dual Ethernet serial over IP solution maintains connection to your critical equipment by automatically switching to its secondary LAN port within 10 milliseconds of a network failure or disruption. Ideal for industrial environments, the serial to Ethernet device server accepts wide-range 12-48V DC power input via a terminal block or an optional DC jack, enabling you to add redundant power with a secondary adapter (e.g. 12V DC 1.5A Power Adapter SKU: IM12D1500P
- sold separately), keeping the device server functional in the event of power surges or failures. This device server supports baud rates up to 460.8 Kbps which provides a smooth, high-speed connection to your serial devices. The device server also offers support for HTTPS, SSH & SSL to ensure secure communication, while integrating remote Telnet configuration & support for IP, HTTP, ICMP, DHCP, ARP, TCP & UDP protocols. You can customize the serial device server to suit your application with versatile browser-based or virtual com port software configuration. Ensuring performance in harsh environments, this serial device server offers 8KV air, & 4KV contact ESD (Electrostatic Discharge) Protection, & features a rugged, IP-30 case design that is both DIN rail & wall-mountable, with an extended operating temperature range (-40°C to 70°C).
...

Remotely manage an industrial RS232 or RS422/485 serial device over an IP network, with redundant 10/100 Ethernet ports. The NETRS232485 Serial Device Server lets you remotely manage an industrial RS232/422/485 serial device over a local or wide area network (LAN/WAN), with redundant power inputs & dual 10/100 Mbps Ethernet ports. To minimize downtime, this intuitive dual Ethernet serial over IP solution maintains connection to your critical equipment by automatically switching to its secondary LAN port within 10 milliseconds of a network failure or disruption. Ideal for industrial environments, the serial to Ethernet device server accepts wide-range 12-48V DC power input via a terminal block or an optional DC jack, enabling you to add redundant power with a secondary adapter (e.g. 12V DC 1.5A Power Adapter SKU: IM12D1500P
- sold separately), keeping the device server functional in the event of power surges or failures. This device server supports baud rates up to 460.8 Kbps which provides a smooth, high-speed connection to your serial devices. The device server also offers support for HTTPS, SSH & SSL to ensure secure communication, while integrating remote Telnet configuration & support for IP, HTTP, ICMP, DHCP, ARP, TCP & UDP protocols. You can customize the serial device server to suit your application with versatile browser-based or virtual com port software configuration. Ensuring performance in harsh environments, this serial device server offers 8KV air, & 4KV contact ESD (Electrostatic Discharge) Protection, & features a rugged, IP-30 case design that is both DIN rail & wall-mountable, with an extended operating temperature range (-40°C to 70°C).
...