- 10 Gigabit Ethernet LRM “long reach multimode” fiber connectivity (802.3aq standard)
- LC duplex connector
- Fits into the

...

The Pro Safe FS116P provides power & data from a single point, using Power over Ethernet (Po E) over a single Cat-5 cable. The sixteen Fast Ethernet ports can be used for any 10/100 Mbps link & eight of these ports can supply industry-standard IEEE 802.3af power. Advanced auto-sensing algorithm gives power only to 802.3af end devices, so no need to worry about damaging proprietary Po E or non-Po E equipment. In addition, it discontinues the power when Po E devices are disconnected. Easy & reliable, the Pro Safe FS116P automatically determines Po E requirements, speed, duplex, & cable type using Auto Uplink. The affordably priced Pro Safe FS116P delivers Po E to any small business network that wants to simplify the installation of wireless access points & IP-based surveillance cameras. These devices are optimally installed on a ceiling or high on a wall, away from most electrical outlets. Po E eliminates the requirement for a dedicated electrical outlet to power these devices. This allows for flexibility in situating devices where AC power is difficult to access & lowers installation costs. Compact & flexible, the Pro Safe FS116P is ideal for small business network that want to inexpensively use Po E to deploy wireless access points & IP-based network surveillance cameras. Choose to plug in up to eight Ethernet or Fast Ethernet devices & mix in up to four 802.3af IP-based devices like wireless access points or IP-based network surveillance cameras. Place these 802.3af-compliant devices where they belong
- high up on walls & ceiling for maximum coverage
- or anywhere else you need them. Power & data are carried over standard Cat-5 cabling. The standards-based Pro Safe FS116P senses & adjusts for network speed & cabling type automatically, for easy integration into your existing 10/100 Ethernet network. For Po E, the switch automatically detects 802.3af-compliant devices, & supplies power as needed. Front panel LEDs keep you informed of switch and

...

The Pro Safe FS116P provides power & data from a single point, using Power over Ethernet (Po E) over a single Cat-5 cable. The sixteen Fast Ethernet ports can be used for any 10/100 Mbps link & eight of these ports can supply industry-standard IEEE 802.3af power. Advanced auto-sensing algorithm gives power only to 802.3af end devices, so no need to worry about damaging proprietary Po E or non-Po E equipment. In addition, it discontinues the power when Po E devices are disconnected. Easy & reliable, the Pro Safe FS116P automatically determines Po E requirements, speed, duplex, & cable type using Auto Uplink. The affordably priced Pro Safe FS116P delivers Po E to any small business network that wants to simplify the installation of wireless access points & IP-based surveillance cameras. These devices are optimally installed on a ceiling or high on a wall, away from most electrical outlets. Po E eliminates the requirement for a dedicated electrical outlet to power these devices. This allows for flexibility in situating devices where AC power is difficult to access & lowers installation costs. Compact & flexible, the Pro Safe FS116P is ideal for small business network that want to inexpensively use Po E to deploy wireless access points & IP-based network surveillance cameras. Choose to plug in up to eight Ethernet or Fast Ethernet devices & mix in up to four 802.3af IP-based devices like wireless access points or IP-based network surveillance cameras. Place these 802.3af-compliant devices where they belong
- high up on walls & ceiling for maximum coverage
- or anywhere else you need them. Power & data are carried over standard Cat-5 cabling. The standards-based Pro Safe FS116P senses & adjusts for network speed & cabling type automatically, for easy integration into your existing 10/100 Ethernet network. For Po E, the switch automatically detects 802.3af-compliant devices, & supplies power as needed. Front panel LEDs keep you informed of switch and

...

The Pro Safe FS116P provides power & data from a single point, using Power over Ethernet (Po E) over a single Cat-5 cable. The sixteen Fast Ethernet ports can be used for any 10/100 Mbps link & eight of these ports can supply industry-standard IEEE 802.3af power. Advanced auto-sensing algorithm gives power only to 802.3af end devices, so no need to worry about damaging proprietary Po E or non-Po E equipment. In addition, it discontinues the power when Po E devices are disconnected. Easy & reliable, the Pro Safe FS116P automatically determines Po E requirements, speed, duplex, & cable type using Auto Uplink. The affordably priced Pro Safe FS116P delivers Po E to any small business network that wants to simplify the installation of wireless access points & IP-based surveillance cameras. These devices are optimally installed on a ceiling or high on a wall, away from most electrical outlets. Po E eliminates the requirement for a dedicated electrical outlet to power these devices. This allows for flexibility in situating devices where AC power is difficult to access & lowers installation costs. Compact & flexible, the Pro Safe FS116P is ideal for small business network that want to inexpensively use Po E to deploy wireless access points & IP-based network surveillance cameras. Choose to plug in up to eight Ethernet or Fast Ethernet devices & mix in up to four 802.3af IP-based devices like wireless access points or IP-based network surveillance cameras. Place these 802.3af-compliant devices where they belong
- high up on walls & ceiling for maximum coverage
- or anywhere else you need them. Power & data are carried over standard Cat-5 cabling. The standards-based Pro Safe FS116P senses & adjusts for network speed & cabling type automatically, for easy integration into your existing 10/100 Ethernet network. For Po E, the switch automatically detects 802.3af-compliant devices, & supplies power as needed. Front panel LEDs keep you informed of switch and

...

NETGEAR presents a great way to increase your networks capability without breaking your budget: the 16-port JFS516. This 10/100 Fast Ethernet switch provides expanded connectivity for small office networks so users no longer have to compete with each other for bandwidth. All of the essential features
- automatic speed & full/half duplex sensing, 200 Mbps throughput per port, Auto Uplink
- are included, but at an economical price that a value-conscious business owner cant ignore.

...

The NETGEAR Pro Safe 16-AP Wireless Management System is an easy to use appliance to simplify the set up & management of wireless networks. Supporting up to 16 access points, the WMS5316 Wireless Management System provides a single location to configure & manage the entire wireless network. Designed for growing companies who dont want the complexity & cost of full wireless controllers, the WMS5316 Wireless Management System delivers centralized management, load balancing, RF management, & guest access via an intuitive interface. Priced far below a full wireless controller, the WMS5316 Wireless Management System provides significant time savings & simplifies the deployment & management of a wireless network. Mimicking the set up process of a single access point, the easy to use WMS5316 Wireless Management System enables even novice users to adopt a centralized management architecture for up to 16 access points. With automatic discovery of all supported access points in the network, the WMS5316 Wireless Management System speeds the configuration of a the wireless network. Automatic Radio Frequency (RF) management & channel selection takes care of optimizing the access points in the network for maximum connectivity, without intervention from the network administrator. A single entry of wireless parameters & security settings can then be pushed out to all of the access points, enabling a fully functional wireless network in minutes. The WMS5316 Wireless Management System monitors the wireless network to ensure optimal performance & respond to changes in the RF environment. It will automatically re-assign channels & adjust RF parameters for maximum connectivity. If enabled, load-balancing on Pro Safe Access Points can ensure that no single access point is overloaded continuously, by diverting clients to nearby access points. By actively managing the wireless network, the WMS5316 Wireless Management System provides an enhanced wireless experience ...

The NETGEAR Pro Safe 16-AP Wireless Management System is an easy to use appliance to simplify the set up & management of wireless networks. Supporting up to 16 access points, the WMS5316 Wireless Management System provides a single location to configure & manage the entire wireless network. Designed for growing companies who don't want the complexity & cost of full wireless controllers, the WMS5316 Wireless Management System delivers centralized management, load balancing, RF management, & guest access via an intuitive interface. Priced far below a full wireless controller, the WMS5316 Wireless Management System provides significant time savings & simplifies the deployment & management of a wireless network. Mimicking the set up process of a single access point, the easy to use WMS5316 Wireless Management System enables even novice users to adopt a centralized management architecture for up to 16 access points. With automatic discovery of all supported access points in the network, the WMS5316 Wireless Management System speeds the configuration of a the wireless network. Automatic Radio Frequency (RF) management & channel selection takes care of optimizing the access points in the network for maximum connectivity, without intervention from the network administrator. A single entry of wireless parameters & security settings can then be pushed out to all of the access points, enabling a fully functional wireless network in minutes. The WMS5316 Wireless Management System monitors the wireless network to ensure optimal performance & respond to changes in the RF environment. It will automatically re-assign channels & adjust RF parameters for maximum connectivity. If enabled, load-balancing on Pro Safe Access Points can ensure that no single access point is overloaded continuously, by diverting clients to nearby access points. By actively managing the wireless network, the WMS5316 Wireless Management System provides an enhanced wireless experience ...

The NETGEAR Pro Safe 16-AP Wireless Management System is an easy to use appliance to simplify the set up & management of wireless networks. Supporting up to 16 access points, the WMS5316 Wireless Management System provides a single location to configure & manage the entire wireless network. Designed for growing companies who don't want the complexity & cost of full wireless controllers, the WMS5316 Wireless Management System delivers centralized management, load balancing, RF management, & guest access via an intuitive interface. Priced far below a full wireless controller, the WMS5316 Wireless Management System provides significant time savings & simplifies the deployment & management of a wireless network. Mimicking the set up process of a single access point, the easy to use WMS5316 Wireless Management System enables even novice users to adopt a centralized management architecture for up to 16 access points. With automatic discovery of all supported access points in the network, the WMS5316 Wireless Management System speeds the configuration of a the wireless network. Automatic Radio Frequency (RF) management & channel selection takes care of optimizing the access points in the network for maximum connectivity, without intervention from the network administrator. A single entry of wireless parameters & security settings can then be pushed out to all of the access points, enabling a fully functional wireless network in minutes. The WMS5316 Wireless Management System monitors the wireless network to ensure optimal performance & respond to changes in the RF environment. It will automatically re-assign channels & adjust RF parameters for maximum connectivity. If enabled, load-balancing on Pro Safe Access Points can ensure that no single access point is overloaded continuously, by diverting clients to nearby access points. By actively managing the wireless network, the WMS5316 Wireless Management System provides an enhanced wireless experience ...

NETGEARs popular FS100 series desktop switches, known for its reliability & performance, provide your LAN with high-speed, 10/100 Mbps auto-sensing connectivity for 16 users. Just plug in your Ethernet cables, connect a power cord, & youre ready to go-theres no software to configure. They negotiate to the fastest possible connection & with Auto Uplink technology, these switches automatically figure out if the link needs a straight through or cross-over connection, & makes the right choice. Existing 10BASE-T devices are easily integrated within higher bandwidth environments, with full wire speeds on all ports of either 10 Mbps or 100 Mbps. Engineered without the need for internal fans, they operate silently. & each of these very compact switches is housed in a sturdy metal case for years of dependable use. ...

NETGEARs JGS516 Gigabit Switch gives your office network a megaboost of speed & capacity that is within your budget. With up to 48 Gbps of bandwidth, this 16-port switch can blast 2000 Mbps per port while its affordable prices enable you to put it everywhere. Use it to take Gigabit Ethernet directly to the desktop! Standards-based for easy integration of 10, 100, & 1000 Mbps devices, this unmanaged, rack-mountable switch feature 10/100/1000 automatic speed on every port. Users can take advantage of its ability to deliver large amounts of multimedia, image, & video information in no time at all. Ideal for workgroups, labs, departments, or growing offices looking for outstanding performance at a low price. ...