About Us
Contact Us
Privacy Policy
Cookie Usage
Add Your Store

More From Contributor

image missing
11/30217470 DC
£20.00
BS EN ISO 17556. Determination of the ultimate aerobic biodegradability of plastics materials in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved Plastics, Polymers, Biodegradability, Degradation, Soils, Oxygen dem&, Biological oxygen dem&, Carbon dioxide, Biological analysis & testing, Microbiological analysis, Aerobic bacteria, Test equipment, Testing conditions, Test specimens, Specimen preparation, Humidity ...
Archived Product
image missing
11/30217476 DC
£20.00
BS ISO 8178-9. Reciprocating internal combustion engines. Exhaust emission measurement. Part 9. Test cycles & test procedures for test bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions Reciprocating engines, Internal combustion engines, Prime movers, Exhaust gases, Pollutant gases, Gases, Combustion products, Emission, Smoke, Particulate air pollutants, Compression-ignition engines ...
Archived Product
image missing
11/30217674 DC
£20.00
BS 5892-8. Railway applications. Wheelsets & bogies. Powered & non-powered wheelsets with inboard bearings. Product requirements Axles, Vehicle suspension systems, Vehicle components, Railway vehicle components, Railway vehicles, Railway equipment, Steels, Chemical composition, Heat treatment, Tensile strength, Proof stress, Elongation, Impact strength, Inspection, Marking, Dimensional tolerances, Machining tolerances, Roughness (surface), Sampling methods, Sample location, Ultrasonic testing, Testing conditions, Magnetic-particle flaw detection, Grades (quality) Railway applications ...
Archived Product
image missing
11/30217702 DC
£20.00
BS ISO 14603. Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for open-hole tension of continuous fibre-reinforced ceramic matrix composites at room temperature Ceramics, Special ceramics, Chemical reactions, Performance, Composite materials ...
Archived Product
image missing
11/30217705 DC
£20.00
BS ISO 14627. Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for fracture resistance of silicon nitride materials for rolling bearing balls at room temperature by indentation fracture method Special ceramics, Test methods, Fracture toughness, Silicones, Rolling bearings, Balls (bearing components), Indentations ...
Archived Product
image missing
11/30217708 DC
£20.00
BS ISO 14628. Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for rolling contact fatigue of silicon nitride ceramics at room temperature by balls-on-flat method Ceramic & glass technology, Monolithic materials, Monolithic structures, Test methods, Ceramics, Special ceramics, Silicon inorganic compounds, Nitrides, Rolling bearings, Balls (bearing components), Bearings, Physical properties of materials, Mechanical properties of materials, Classification systems, Specimen preparation ...
Archived Product
image missing
11/30217714 DC
£20.00
BS EN ISO 15184. Paints & varnishes. Determination of film hardness by pencil test Paints, Coatings, Varnishes, Hardness testing, Films (states of matter), Test specimens, Test equipment, Specimen preparation, Testing conditions, Reproducibility, Panels ...
Archived Product

11/30217696 DC

BS ISO 23317. Implants for surgery. In vitro evaluation for apatite-forming ability of implant materialsImplants (surgical), Surgical equipment, Orthopaedic equipment, Bones, Surfaces, Coatings, Apatite, Chemical analysis and testing, Qualitative analysis
RIP - This product is no longer available on our network. It was last seen on 26.10.2012

This page now acts as a permanent archive for this product. Add more information using the comments box below to ensure it can still be found by future generations.

Use our search facility to see if it is available from an alternative contributor.
  • Availability: Out Of Stock
  • Supplier: BSI
  • SKU: 000000000030217696
Availability: In Stock
£20.00
books Books
Description Reviews / Comments Add New

Product Description

BS ISO 23317. Implants for surgery. In vitro evaluation for apatite-forming ability of implant materials Implants (surgical), Surgical equipment, Orthopaedic equipment, Bones, Surfaces, Coatings, Apatite, Chemical analysis & testing, Qualitative analysis

Reviews/Comments

Add New

Intelligent Comparison

Oooops!
We couldn't find anything!
Perhaps this product's unique.... Or perhaps we are still looking for comparisons!
Click to bump this page and we'll hurry up.

Price History

Oooops!
We couldn't find any historical pricing!

Vouchers

No voucher codes found.
Do you know a voucher code for this product or supplier? Add it to Insights for others to use.

Facebook

Jargon Buster

DC - Direct Current
Equipment - A product or good that is tactile.

Supplier Information

BSI
The British Standards Institution are a non profit making organisation, who produce standards and standard related services, for a variety of industries. The standards that they produce are used as a guideline or definition of the minimum levels certain services and product should reach. The standards are produced by BSI directly, following consultations and public enquiries. At shop.bsigroup.com, you can purchase a variety of standards. They stock documents for industries such as food and drink, engineering, building and construction, energy and utilities, transport and agriculture and farming. If you become a member of their site you can get huge discounts on their standards. They also offer training courses and conferences via their website, or you could take advantage of their online standards tools.
Page Updated: 2016-12-15 11:58:50

Community Generated Product Tags

Oh No! The productWIKI community hasn't generated any tags for this product yet!
Menu