United Kingdom
France
Germany
Netherlands
Sweden
USA
Italy
Spain
Car Accessories>Workshop & Garage Tools>Servicing Tools>Steering & Suspension Tools
Available
-
Innovative tool saves
time, money and
frustration. Installs
CVJ boots without
removing drive shafts
from the vehicle or the
CV joint from the drive
shaft. No effort and no
mess! Save on labour
time by up to 70% and
prevent damage to CV
joint. Composite body
with simple control
valve, works from
standard workshop air
supply. While fitting
boot the tool can be
removed from the air line
when pressurized (arms
open) and will maintain
pressure until the
release button is
pressed. Suitable for
cars and light commercial
vans. Model No. BSL103
Availability: In Stock
£103.20
Available
-
Suitable for removal and
installation of spring
and shock strut from
steering
knuckle. Prevents
expensive damage to
aluminium or cast iron
steering hubs. Excellent
also for spreading the
clamp on lower ball
joints. Wide range of
vehicle
applications. Model No.
VS390
Availability: In Stock
£71.94
Available
-
Suitable for the
removal/installation of
the rear trailing arm
mounting bushes on Ford
vehicles. Can be used in
situ without removing the
arm from the
vehicle. Also suitable
for some Volvo vehicles
that share the same Ford
platform. Supplied in
carry-case. Model No.
VSE4784
Availability: In Stock
£299.94
Available
-
Specialized tool designed
for checking and
adjusting oil levels on
all conventional and
single chamber cartridge
motorcycle
forks. Supplied with
adjustable ring and oil
pipe to measure oil
levels from 0-290mm in
5mm increments. Features
top-up syringe with 70ml
capacity. Can also be
used on bicycles equipped
with front
suspension. Model No.
MS033
Availability: In Stock
£46.14
Available
-
Unique design allows for
the two halves of the
thread restorer to be
fitted on the good thread
and wound back over the
damaged thread, normally
at the end of the
stud. Traditional thread
restorers rely on luck
for the restored and
undamaged threads to
align. Kit contains the
three most common wheel
stud thread
sizes. Thread Sizes:
12x1.25, 12x1.5,
14x1.5mm. Supplied in
storage case.
Availability: In Stock
£37.74
Available
-
Quality made tool
designed to aid fast
tensioning and securing
of CVJ boot banding
material. Simply insert
banding, tension using
winding mechanism, and
then pull over lever to
cut the band to
length. Fitted with
large and comfortable
handle grip. Model No.
VS1636
Availability: In Stock
£25.74
Available
-
High security coil spring
compressor with 1200kg
maximum capacity per
pair. Features
adjustable safety bar for
additional security and
compressors have lower
safety jaws for ultimate
peace of mind. Use 19mm
hex socket or
spanner. Spring not
included
Availability: In Stock
£215.94
Available
-
1500kg Capacity air
actuated hydraulic unit
with alternative foot
operation. Quicker and
easier than using ratchet
driven spring
compressor. Plastic
coated yokes reduce the
risk of spring
slippage/damage. Suitable
for springs from Ø80mm
to Ø175mm. Model No.
RE232
Availability: In Stock
£473.94
Available
-
Designed for use on
wishbone suspension using
access points in the rear
suspension arm. Features
two pairs of carefully
shaped yokes that prevent
the coil spring from
bowing. Saves time over
traditional methods of
demounting
springs. Applications:
Fiat, Hyundai, Mazda,
Mercedes, Mitsubishi,
Nissan, Peugeot, Rover,
Saab, Toyota, Volvo,
VW. Supplied in
carry-case. Model No.
RE2280
Availability: In Stock
£239.94
Available
-
Fast and safe compression
of road springs. 1000kg
Air operated unit with
safety locking guard.
Supplied with two
interchangeable plastic
coated lower yokes and a
suspension strut
clamp. Fits a wide range
of spring configurations
and diameters. Also
features a strut locating
platform for easy
movement of the
suspension strut to avoid
unnecessary
lifting. Model No. RE300
Availability: In Stock
£935.94
Available
-
Compact design for use on
wishbone suspension using
access points in the rear
suspension arm. Includes
two pairs of carefully
shaped yokes that prevent
the coil spring from
bowing and a drive
extension for use in
restricted
areas. Size/Suitability:
Ø60-170mm. Jaw Opening:
30-245mm. Drive: 20 &
23mm Hex. Saves time
over traditional methods
of demounting
springs. Supplied in
carry-case. Model No.
RE2281
Availability: In Stock
£239.94
Available
-
2250kg Maximum jaw
loading with 2.9 x safety
factor. Supplied with
two pairs of drop-forged
yokes. Safety yokes
carefully shaped to
prevent coil spring from
bowing. Suitable for use
with air impact
wrenches. Wide
availability of standard
and optional
yokes. Standard yokes
included. Made in
Europe. Spring not
included
Availability: In Stock
£635.94
Available
-
Designed to relieve fork
spring tension allowing
removal of the tube caps
from the rod, without
damaging the
threads. Can be used
with the fork in situ or
on the bench. Fits most
modern road
motorcycles. Use with
17mm socket. Maximum
Reach: 750mm. Maximum
Fork Tube Diameter:
32mm. Model No. MS1824
Availability: In Stock
£125.94
Available
-
Aluminium gauge bodies
with chemically blackened
wheel stud
locators. Measures wheel
geometry by attaching
calibrated bubble levels
to the wheel studs. For
accurate results these
tools should be used with
Model No. GA44 Steering
Turntables. Supplied in
a steel case together
with operating
instructions. Model No.
GA42
Availability: In Stock
£461.94
Available
-
Robust, magnetic gauge
mounts onto hub for quick
and accurate measurement
of camber, castor angles
and kingpin
inclination. Two large
adjuster knobs, one for
conveniently zeroing
bubble during angle
measurement and one for
adjusting kingpin
inclination. Camber
gauge with fixed
graduation from +5° to
-5°. Adjustable castor
gauge graduated from
+11° to -3°. Kingpin
gauge graduated from 0°
to 14° left to
right. Magnetic plate
Ø: 85mm. Supplied in
tough composite
carry-case. Model No.
GA450
Availability: In Stock
£149.94
Available
-
Suitable for the in situ
removal and installation
of front lower ball
joints on Mercedes W220,
W211, W230 and Renault
Megane. No need to
disassemble. Also
includes a selection of
multipurpose sleeves,
which have various
automotive
applications. External
Sleeve Sizes: Ø50.5,
63.5, 76mm. Use with
ratchet wrench. Model
No. VS1274
Availability: In Stock
£257.94
Available
-
Robust, magnetic gauge
mounts onto hub. Quick
and accurate measurement
of camber and castor
angles. Large adjuster
knob for convenient
zeroing of bubble during
castor angle
measurement. Graduated
from +6° to
-6°. Supplied in
carry-case. Model No.
GA45
Availability: In Stock
£71.34
Available
-
Essential for the
assembly and disassembly
of suspension units.
Suitable for most types
of classic and modern
motorcycle coil
springs. Supplied with
four spare plastic spring
protectors in metal
storage case. Use with
ratchet wrench. Model
No. VS1824
Availability: In Stock
£68.34
Available
-
Heavy-duty ball joint
splitter suitable for HGV
vehicles. Specially
designed to be operated
manually or by 12tonne
hydraulic ram
supplied. Features a
step down thread adaptor
that allows fitting of
the manual thrust screw
or hydraulic
ram. Supplied in
carry-case. Model No.
VS3813
Availability: In Stock
£269.94
Available
-
Extra heavy duty puller
for the removal of drop
arms from the toughest
of vehicle applications
Ideal for Land Rover
Discovery 1 & 2, Range
Rover P38, Land Rover
Defender and Ford Transit
applications The puller
is designed to be used
with the steering box
already removed from the
vehicle Includes a
force screw allowing a
technician to effectively
shock the drop arm to
become loose from the
steering box Jaw spread
capacity - 60mm Jaw
reach capacity - 80mm
Availability: In Stock
£356.51
Available
-
Multi-purpose ball joint
dust covers easily
replace split or damaged
dust covers on otherwise
serviceable ball joints,
avoiding MOT test
failure. Pack contains 3
ball joint dust covers
supplied with retaining
'O' rings and fitting
tool. Covers a wide
range of commercial
vehicle
applications. Model No.
RJC02
Availability: In Stock
£19.14
Available
-
Multi-purpose ball joint
dust covers easily
replace split or damaged
dust covers on otherwise
serviceable ball joints,
avoiding MOT test
failure. Pack contains 6
ball joint dust covers
supplied in 3 different
sizes with retaining 'O'
rings and fitting
tool. Covers a wide
range of car and small
commercial vehicle
applications. Model No.
RJC01
Availability: In Stock
£29.46
Available
-
460mm Tool gives deep
access particularly
suited to adjustment of
motorcycle
carburettors. 110°
Angled head gives
improved access to
hard-to-reach areas. One
turn of handle equals one
turn of slotted
blade. Blade tip height
is adjustable allowing it
to be set in place during
operation. Model No.
MS013
Availability: In Stock
£30.54
Available
-
Fast and simple to
use. Kit includes 56mtr*
of high quality stainless
steel banding with a
tensile strength of
420N/mm². Dispenser
case also houses 150*
clamp sets and unique
pliers with integrated
cutters and band
tensioner. Never be
caught without the right
sized boot clamp
again. Model No.
BSL102 * Approximate
quantities
Availability: In Stock
£76.74
Available
-
Suitable for internal and
external applications
Hydraulic ram requires no
power - develops up to 10
tons of pressure with
hand power only
Components are made of
hardened, heat treated
(HRC 42-45”) Chrome
Vanadium steel for
ultimate strength
Performs 2 or 3 leg
pulling Set includes -
10 ton hydraulic ram
(Ø38mm) with bar - 3 x
100mm gear puller legs,
3 x 150mm gear puller
legs and 3 x 200mm gear
puller legs - Twin head
for use as a 2 leg puller
and triple head for use
as a 3 leg puller - 2 x
extension rods: Ø25mm x
50mm (L) and Ø25mm x
100mm (L) - 4 x main
rods: 200mm - Two-way
cross beam - Bearing
separator: Ø20-105mm
capacity - Centre
adapter - Bolt and ram
nut Weight: Approx.
18kgs Warranty: 2 Years
Availability: In Stock
£203.99
Available
-
Innovative tool saves
time, money and
frustration. Install CVJ
boot without removing
drive shaft from the
vehicle or the CV joint
from the drive shaft. No
effort and no mess! Save
on labour time by up to
70% and prevent damage to
CV joint. Composite body
with 8.5mm hex
drive. Used in
conjunction with drill
with standard
chuck. Fingers are
mechanically open/closed
by the rotation of the
drive. Maximum Joint
Diameter:
110mm. Suitable for cars
and light commercial
vans. Model No. BSL104
Availability: In Stock
£167.94
Available
-
Taps and dies are
suitable for chasing out
damaged threads and the
removal of nicks and
burrs without
undercutting good
threads. Use with a
standard spanner and a
little light oil. Thread
file restores damaged
external threads on any
diameter, right or left
hand - just select
correct pitch. Ideal for
restoration
work. Supplied in tool
tray.
Availability: In Stock
£65.94
Available
-
Taps and dies are
suitable for chasing out
damaged threads and the
removal of nicks and
burrs without
undercutting good
threads. Thread file
restores damaged external
threads on any diameter,
right or left
hand. Supplied in
carry-case. Model No.
AK311
Availability: In Stock
£167.94
Available
-
Forged steel body ball
joint splitter suitable
for light commercial
vehicles. Specially
designed to be operated
manually or by 1.5tonne
hydraulic ram
supplied. Features a
step down thread adaptor
that allows fitting of
the manual thrust
screw. Model No. VS3811
Availability: In Stock
£83.94
Available
-
Low profile set suitable
for most modern
vehicles. Three sizes of
jaw allow use on most
cars and light commercial
vehicles. Jaw
Capacities: Small 23mm,
Medium 28mm, Large
34mm. Features
heavy-duty forged steel
body and hardened screw
with thrust
ball. Supplied in
carry-case. Model No.
VS3800
Availability: In Stock
£110.34
Available
-
Upgrade RE230 Strut &
Spring Compressing
Station into RE231 Coil
Spring Compressing
Station. Wider range of
vehicle
applications. Two pairs
of spring yokes and upper
and lower yoke
carriers. Includes
safety chain. Spring
Diameter:
80-175mm. Maximum Load:
1000kg. Model No.
RE230UK
Availability: In Stock
£135.54
Available
-
Universal tool set for
extracting and drawing-in
of bushes, bearings,
seals etc Standard
Universal applications -
Car - LCV - HGV
Contains x20 Press
Sleeves Inside Diameter
Range: 34 - 72mm
Outside Diameter Range:
44 - 82mm 4x Step
Plates 4x pulling
spindles with thrust
bearings
Availability: In Stock
£639.58
Available
-
Unique Sykes-Pickavant
design of vice-mounted
Coil Spring
Compressor Features
double-ended hex drive (2
x 24mm hex) for ease of
use Can be operated
from either end using
ratchet or 24mm
wrench Hex drives at
both ends, incorporate
shear-pins for safety
Features external thrust
bearing for ease of
service Heat treated,
Self-lubricating
operating screw Safe
Working Load =
15000N Supplied with two
sets of universal
jaws: Medium Jaws –
110-150mm diameter
Large Jaws – 140-195mm
diameter
Availability: In Stock
£673.04
Archived Product
-
For removal and
installation of steering
rack knuckles - 35 to
45mm diameter Works on
all steering racks with
track rods up to 30mm
diameter Self locking
rollers adjust
automatically to the
required knuckle
diameter, to provide
safe and secure grip
Manufactured to OEM
specifications, as
required by Mercedes,
PSA, Renault, Toyota,
VW Group etc High
Quality Grade Steels:
Forged Steel body Heat
treated steel rollers
Steel tube with 30mm
diameter hex
Serviceable – Roller
cage is replaceable
should the rollers become
worn or damaged
Availability: In Stock
£148.20
Available
-
Set of nine aluminium
bearing and seal
drivers. Suitable for
straight installation of
bearing race without
damage to the bearing or
axle housing. Fits most
popular bearing race
sizes. Driver Sizes:
39.5, 44, 50, 59, 63,
64.5, 72, 76,
81mm. Model No. VS703
Availability: In Stock
£71.94
Available
-
Set of nine heavy-duty
steel bearing and seal
drivers. Suitable for
straight installation of
bearing race without
damage to the bearing or
axle housing. Fits most
popular bearing race
sizes. Driver Sizes Ø:
39.5, 44, 50, 59, 63,
64.5, 72, 76,
81mm. Model No. VS7031
Availability: In Stock
£39.54
Available
-
2500kg Maximum
loading. Heavy-duty,
lightweight unit made
from high tech steel
alloy. Supplied with one
pair of yokes that will
cover 90% of the car
market. Safety yokes,
with polyurethane inserts
for improved grip, are
carefully shaped to
prevent the coil spring
from bowing. Yoke
brackets are adjustable
to suit all types of
springs, including
conical. 1/2"Sq Drive
for direct use with most
air wrenches. Made in
Europe. Spring not
included
Availability: In Stock
£767.94
Available
-
Diameter/Length:
Ø36/350mm. Simple but
ingenious tool that tests
for movement and wear in
suspension components
such as ball joints,
bearings and
bushes. Lower the road
wheel on the roller bar
using a 1/2"Sq drive
breaker bar to rock the
road wheel to highlight
any movement. Ideal for
use on a platform
ramp. Model No. VS3816
Availability: In Stock
£47.94
Available
-
Designed for the second
generation of wheel
bearing found on modern
vehicles. These bearings
are lightweight with an
integral mounting
flange. They are also
pre-loaded with a
retaining ring that
secures the bearing into
the housing. Suitable to
be used in situ when
replacing the front wheel
bearings. Supplied in
carry-case. Model No.
VS7030
Availability: In Stock
£443.94
Available
-
Suitable for MacPherson
strut coil
springs. Features a yoke
extension bracket that
also allows use on
conical
springs. Supplied with
three pairs of different
sized interchangeable
yokes, for a wide range
of vehicle applications
and plastic yoke
protectors that protect
the spring coating from
damage which can
invalidate the vehicle
manufacturer's
warranty. Safety yokes
carefully shaped to stop
the spring bowing while
under compression. Model
No. RE229
Availability: In Stock
£359.94
Available
-
Designed for the second
generation of wheel
bearing found on modern
vehicles. These bearings
are lightweight with an
integral mounting
flange. They are also
pre-loaded with a
retaining ring that
secures the bearing into
the housing. Suitable to
be used in situ when
replacing the front wheel
bearings. Supplied in
carry-case. Model No.
VS7028
Availability: In Stock
£335.94
Available
-
Universal CVJ boot made
from high quality
neoprene material
suitable for use with air
operated boot
installation tools.
Supplied with fitting
kit including clips,
grease sachet and cutting
guide. Suitable for 98%
of vans and light
commercial
vehicles. Joint Ø:
80-120mm. Shaft Ø:
28-40mm. Model No. CV88
Availability: In Stock
£19.14
Available
-
Universal CVJ boot made
from high quality
elastomer material
suitable for use with air
operated boot
installation
tools. Supplied with
fitting kit including
clips, grease sachet and
cutting guide. Suitable
for most car and car
derived van
applications. Model No.
CV96
Availability: In Stock
£10.14
Available
-
Universal CVJ boot made
from high quality
neoprene that is
resistant to grease,
water, ozone, abrasion
and extremes of
temperature. Suitable
for 98% of cars and car
derived vans. No
dismantling of
joint/shaft required and
can be fitted in 20
minutes. Supplied with
fitting kit including
clips, grease sachet,
disposable gloves, glue,
cutting guide and
fitting
instructions. Joint Ø:
56-120mm. Shaft Ø: 19 -
35mm. Model No. CVS18
Availability: In Stock
£16.74
Available
-
Designed to be used with
a standard workshop
press. Multiple threaded
drillings in aluminium
base plate allows the
support bars to be
installed in virtually
any position, allowing
the bearing or bush to be
positioned
horizontally. Includes a
packing block for added
versatility. Ideal for
the removal of wheel
bearings and
bushes. Model No. VS7036
Availability: In Stock
£239.94
Available
-
Suitable for packing
bearings with an even
spread of grease. Clean,
quick operation simply
place bearing on to the
bottom cone, screw down
the cone lid and pump
grease in to
nipple. Works on most
tapered roller bearings
fitted on cars, boats,
trailers, etc. Both
cones feature knurled
grips for use with oily
fingers. Suitable for
use with Sealey and other
best selling grease guns.
Availability: In Stock
£10.14
Available
-
Contains the four most
common wheel bolt thread
sizes. Suitable for
cleaning and repairing
damaged wheel hub
threads, saving time and
money. Use with 12mm
socket or
spanner. Thread Sizes:
M12 x 1.25mm, M12 x
1.5mm, M12 x 1.75mm,
M14 x 1.5mm. Supplied
in storage case. Model
No. SX205
Availability: In Stock
£39.54
Available
-
Suitable for the fast
removal/installation of
the steering knuckle.
Designed to fit over
the steering shaft onto
the steering rack. Three
interchangeable heads fit
racks with hex drive,
two flats and round ends
with a diameter of 30 to
45mm. Model No. VS4003
Availability: In Stock
£235.14
Available
-
Suitable for fast and
easy removal of the
steering knuckle. Fits
racks with hex drive,
two flats and round
ends. Ideal for vehicles
with limited access and
avoids the need to remove
the rack
assembly. Suitable for
steering rack knuckles
with a diameter of
40-54mm. Model No.
VS4004
Availability: In Stock
£40.74
Available
-
Suitable for the fast and
easy removal of the
steering knuckle. Fits
racks with hex drive,
two flats and round
ends. Ideal for vehicles
with limited access and
avoids the need to remove
the rack
assembly. Suitable for
steering rack knuckles
with a diameter of 33 to
41mm. Model No. VS4000
Availability: In Stock
£29.94
Available
-
Comprehensive kit for
fast and effective in
situ removal/installation
of wheel bearings,
suspension bushes and
seals. Reduces the
possibility of damaging
the bearing/suspension
housings. Supplied with
four stepped end plates
and four force screws in
carry-case. Plates and
sleeves can also be used
in a standard workshop
press when in situ access
isn't possible. Model
No. VS7023A
Availability: In Stock
£581.94
Available
-
Designed for the second
generation of wheel
bearing found on modern
vehicles. These bearings
are lightweight with an
integral mounting
flange. They are also
pre-loaded with a
retaining ring that
secures the bearing into
the housing. Suitable to
be used in situ when
replacing the front wheel
bearings. Supplied in
carry-case. Model No.
VS7029
Availability: In Stock
£335.94
Available
-
Universal support for use
with a workshop press
Three point contact
guarantees a perfect,
safe support Easily
press bearings on a wide
variety of suspension
arms Adjustable height
anvil bolts Swivel
element for added
versatility Safety
alignment brackets for
security on press
Availability: In Stock
£419.16
Available
-
Comprehensive kit for
fast and effective in
situ removal/installation
of wheel bearings,
suspension bushes and
seals. Reduces the
possibility of damaging
the bearing/suspension
housings. Supplied with
twenty two adaptors from
44 to 90mm and five force
screws in
carry-case. Adaptors can
also be used in a
standard workshop press
when in situ access isn't
possible. Model No.
VS7026
Availability: In Stock
£359.94
Available
-
New lightweight design
for the installation of
bearings without damaging
the bearing or
housing. Contains 3
metal bearing drift
sleeves and 34 nylon
drifts. Can also be used
to install oil
seals. Fits most sizes
of bearing and seals
found on modern
vehicles. Supplied in
carry-case. Model No.
VS7024
Availability: In Stock
£197.94
Available
-
Suitable for removing and
installing the upper
front ball joint in situ
without the need to
disassemble. Features a
variety of adaptors used
in different combinations
for extracting and
installing. Supplied in
a carry-case with each
part numbered for simple
selection. Model No.
VSE725
Availability: In Stock
£239.94
Available
-
Hydraulic hand pump unit
powers 1tonne capacity
ram and yoke
assembly. Up to 50%
quicker than using other
ratchet driven spring
compressors. Equipped
with two pairs of spring
yokes with plasticized
covers to prevent
slippage and damage to
springs. Suitable for
springs from 80mm ID to
165mm OD. Model No.
VS7011
Availability: In Stock
£353.94
Available
-
Universal CVJ boot made
from high quality
elastomer material
suitable for use with air
operated boot
installation
tools. Supplied with
fitting kit including
clips, grease sachet and
cutting guide. Suitable
for most car and car
derived van
applications. Joint Ø:
56-116mm. Shaft Ø:
19-28mm. Pack Qty: 12 x
Model No. CV96. Model
No. CV9612
Availability: In Stock
£115.14
Denmark